1989 Chevrolet Cheyenne R3500 Mason Dump on 2040-cars
Deep River, Connecticut, United States
For Sale is a 1989 Chevrolet Cheyenne R3500 2wd Mason Dump Truck. Truck has a 350 Gas engine in in that runs great as well as a 3 speed manual transmission with a brand new clutch installed. Truck is 2wd and has recently new battery, entire front copper brake lines, front tires, oil change. Good Work Truck (was used to haul leaves in fall only) has extra helper springs in rear suspension and the dump is electric hydraulic NOT the pto. Truck has 99,704 original miles. Will need rear tires, new trailer hitch (one on it was bent by previous owner). Dump body has some rust but is still in overall good shape no holes, front suspension is rusty, rear is clean. Pics are posted can take more if there is a specific area you'd like to see. Asking $3900 Drive it away clean title in hand LOCAL PICKUP ONLY, no nonsense no shipping. $500 NON-REFUNDABLE DEPOSIT DUE within 24hours of Sale.
|
Chevrolet Cheyenne for Sale
Auto Services in Connecticut
Wilton Auto Body Repair ★★★★★
Suburban Subaru ★★★★★
Stanley`s Auto Body ★★★★★
Shippan Auto Body ★★★★★
Safelite AutoGlass - North Haven ★★★★★
S & J Automotive ★★★★★
Auto blog
Final C6 Corvette built in Bowling Green
Fri, 01 Mar 2013With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.
GM recalling nearly 4,000 vehicles over airbag concerns
Thu, 31 Jan 2013Four different General Motors vehicles from the 2012 model year are being recalled over a potential airbag issue. The driver's side airbag shorting bar in the 2012 Buick Verano and 2012 Chevrolet Camaro, Cruze and Sonic might make contact with the airbag terminals, even during a crash. If so, the airbag won't deploy when it should, possibly increasing injury to the driver.
The recall is expected to begin on February 13 for the 3,896 units that might be affected. GM will notify owners who can then take their vehicles to dealers to have the airbag coil replaced. A bulletin from the National Highway Traffic Safety Administration below has more info.
Why does the Corvette Stingray have so many vents? Here's why
Sun, 27 Jan 2013Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.