1929 Model A Tudor Sedan Ready For Restore Hotrod Ratrod on 2040-cars
Fayetteville, Arkansas, United States
Engine:Gas
Vehicle Title:Clear
Drive Type: Rear
Make: Ford
Mileage: 999,999
Model: Model A
Number of Cylinders: 4
Trim: Sedan
1929 Model A Tudor Sedan
I have for sale a 1929 Ford, Model A Tudor Sedan, almost complete, lots of new parts, ready to be finished and restored. I purchased this a few years ago, been purchasing parts here and there, in hopes that I would be able to put it together some day and enjoy it when it was complete. Due to health and tired of waiting, I decided to buy one that was complete and ready to drive. I absolutely love it and have decided to sell this one, along with all its parts, new and old. This project is literally ready to be put together. I have a lot of money tied up in this project and a lot of new parts. I have included a parts list below of all the new parts that will go with this project and have included as many pictures that eBay would allow. The vehicle comes with a clean Arkansas title!
The body is in good condition with surface rust throughout and typical cancer on front lower cowls, bottom doors and rear fender wells. I have new patches to fix the front lower cowl and rear fender wells (see parts list). Body is fairly straight with a few dings in places, but overall in great condition for its age. Body needs blasted, patches installed and paint. I have brand new metal fenders for the front (see parts list), but you will need to find fenders for the rear as well as the running boards. I purchased all new boards for the top/roof of vehicle along with new material to wrap it with (see parts list).
On the inside, I have all of the glass except for the passenger front door glass, it has the original floor boards, the driver side seat and the rear seat. The passenger side seat will need to be found and purchased. All seats need to be reupholstered. For some reason, I forgot to take picture of all the interior pieces, but they are included. I have the dash, all door panels and misc. trim.
The rolling chassis has been completely gone through and painted black. The rear axle has been rebuilt, front and rear hubs, as well as the transmission. Chassis is sitting on 19" wheels that could use a better paint job with fairly new tires. I will include an original set of used 21" wheels (see picture), with new tubes and brand new BFG tires (see parts list).
You will receive 2 engines with this vehicle. One came off of the rolling chassis described above. Engine ran fine, but had some blow by and was removed to have rebuilt (still needs rebuilt). The second engine came with this Model A when I purchased it, was told that it ran, but never did hear it do so, but does turn over fine.
Parts list below are of all new parts that have been purchased and that are included with sale. Over $4000 in just new parts (2006 pricing, sells for more now), Chassis including rebuild over $3000, plus the price of actual car. Perfect for someone who is a collector or wants to put this together to flip.
-PAYMENT/SHIPPING -
You are bidding on this 1929 Model A Tudor Sedan. Whomever wins this auction will be responsible for picking this up. I may deliver to anyone in Arkansas or the surrounding areas for a fee, please contact me for possible arrangements.
I am asking for a $1000.00 deposit through PayPal at the time of listing end, and will accept the remainder in Cash or a Cashiers Check only at the time of pick up. If you win this auction, the payment is expected and arrangements need to be made within 5 days after sale ends. If you choose to back out or cancel this transaction, only 50%, or in this case $500.00 of the $1000.00 deposit will be refunded back to you. If you have any questions, please feel free to ask. Thanks for looking!
- 1929 FORD MODEL A TUDOR PARTS LIST -
Quantity: Description: Price: (2006 pricing)
( 5 ) ( 450-21 BFG Tires - Black - $101.91 ea ) ( $509.55 )
( 5 ) ( A-21 TR127 Nickel Stem Tubes - $24.95 ea ) ( $124.75 )
( 1 ) ( Front Fender A1605A - metal ) ( $449.95 )
( 1 ) ( Front Fender A16006A - metal ) ( $449.95 )
( 1 ) ( Hood Shelves A16713/14S - pair ) ( $32.50 )
( 1 ) ( Running Board Shields A16535-6B - set ) ( $154.50 )
( 1 ) ( Radiator Shell Plate A8200AC ) ( $139.95 )
( 1 ) ( Radiator Emblem A8212A ) ( $16.95 )
( 1 ) ( Front Lower Apron Between Fender A16527 ) ( $29.95 )
( 1 ) ( Headlights A13056AR - set ) ( $295.00 )
( 1 ) ( Wiring Harness A14403C ) ( $36.95 )
( 1 ) ( Ignition On Switch A11575F ) ( $21.95 )
( 1 ) ( Nuts A14561W - box ) ( $2.00 )
( 1 ) ( Terminal Box Lid A14561A ) ( $3.95 )
( 4 ) ( Spark Plugs - $4.95 ea ) ( $19.80 )
( 1 ) ( Ignition Points Set - .018 .022 A12199 ) ( $9.95 )
( 1 ) ( Condenser A12300 ) ( $3.95 )
( 1 ) ( Rotor A12200 ) ( $3.95 )
( 1 ) ( Spark Plug Connectors - set of 4 ) ( $1.95 )
(7 yd ) ( Roof Material - $4.95 per yard ) ( $34.65 )
(24 yd) ( Top Cloth Medium Welt - $0.50 per yard ) ( $12.00 )
( 1 ) ( A 1035-1 Header Wood ) ( $66.50 )
( 1 ) ( Bolts - Fender ) ( $14.50 )
( 2 ) ( Window Cranks - $8.95 ea ) ( $17.90 )
( 1 ) ( Front Floor Mat ) ( $39.95 )
( 1 ) ( Rear Floor Mat ) ( $59.95 )
( 5 ) ( Hub Caps ) ( $49.75 )
( n/a ) ( 4.972 yds 1-5 Fancy Upholstery ) ( $23.87 )
( n/a ) ( 3.694 yds 1-5 Fancy Upholstery ) ( $17.73 )
( n/a ) ( Chassis/ Window Channel ) ( $42.95 )
( n/a ) ( Cradle/Starter Crank ) ( $9.95 )
( 2 ) ( 28-31 Running Board Bracket anti Squeak Welt - rolls ) ( $5.50 )
( 1 ) ( 28-29 Radiator to Shell Mounting Set - 12 pc - set ) ( $1.25 )
( 1 ) ( 28-30 Radiator Emblem/Script/Blue on Chrome ) ( $38.50 )
( 1 ) ( 28-29 Crank Hole Cover w/ Rivet/stainless steel ) ( $2.90 )
( 5 ) ( Rim Liners 17" - 21"/ 26-48 ) ( $14.75 )
( 1 ) ( Instrument Panel Screw Set - 28-Mid30 - set ) ( $1.00 )
( 1 ) ( Body to Frame Welt w/adhesive backing 1/8"x2"x20' - roll ) ( $24.95 )
( 1 ) ( 28-28 Radiator Mounting Kit/original style - kit ) ( $3.95 )
( 2 ) ( 28-29 Hood Retainer- $6.20 ea (cancelled 1 Hood Retainer) ) ( $12.40 )
( 2 ) ( 28-31 Tudor, Fordor, Phaeton Rear Fender Brace ) ( $35.00 )
( 2 ) ( 16" Fender Welting ) ( $16.00 )
( 1 ) ( 28-29 Hood Hinge Rods in Stainless ) ( $12.75 )
( 1 ) ( Hood Corner Pads ) ( $3.50 )
( 1 ) ( Hood Prop Kit ) ( $28.05 )
( 1 ) ( Hood Retainer SS scs 28-29 ) ( $3.00 )
( 2 ) ( 28-29 Hood Retainer Shim ) ( $1.40 )
( 1 ) ( 28-29 Hood Cowl Lacing Hook ) ( $1.95 )
( 4 ) ( 28-29 Hood Latch - $8.00 ea ) ( $32.00 )
( 1 ) ( Hood Latch SCS 28-29 ) ( $2.60 )
( 1 ) ( Hood Latch Pads ) ( $1.75 )
( 1 ) ( Hood Latch Bumpers ) ( $4.95 )
( 1 ) ( 28-29 Tudor Sedan Body to Frame Bolt Set ) ( $6.75 )
( 1 ) ( 28-29 Tudor Sedan Top Wood & Screw Kit ) ( $30.50 )
( 1 ) ( 28-29 Tudor Sedan Top Wood Kit ) ( $432.00 )
( 1 ) ( Rear Inner Fender Patch Panels - set (LH & RH) - 2 HUMP/28-31 ) ( $55.25 )
( 1 ) ( Cowl Quarter Patch Panels - set (LH & RH) - 28-29 ) ( $40.75 )
( 1 ) ( 28-29 Body Mounting Wood Block Set /7 pc/ Tudor - set ) ( $42.25 )
( 2 ) ( 28-31 Front Running Board Brackets 17" ) ( $55.00 )
( 1 ) ( 28-31 Running Board Bracket / Left Rear ) ( $27.50 )
( 1 ) ( 28-31 Running Board Bracket/ Right Rear ) ( $27.50 )
( 1 ) ( 28-31 Running Board Bracket Bolt Set/ 36 pc - set ) ( $4.25 )
( 1 ) ( 28-31 Gas Gauge ) ( $34.95 )
( 4 ) ( 28-31 Window Riser Escutcheons ) ( $19.80 )
( 1 ) ( 28-31 Slide Lock Knob ) ( $3.95 )
( 1 ) ( 28-29 Locking Door Handle ) ( $31.95 )
( 1 ) ( 28-31 Stainless Steel Conduit (3) - set ) ( $10.95 )
( 1 ) ( 28-29 Non Locking door Handle ) ( $31.95 )
( 1 ) ( 28-31 Gas Tank Filter ) ( $6.50 )
( 1 ) ( 26-32 Pivot Bolt Set - 2 ) ( $4.25 )
( 1 ) ( 28-31 Inside Sliding Lock Escutcheon ) ( $4.95 )
( 1 ) ( 28-31 Sliding Door Lock Screws - set - 2 ) ( $1.25 )
( 1 ) ( 26-31 Stainless Steel Windshield Swing Arms - set - 2 ) ( $18.91 )
( 1 ) ( 28-31 Inside Sliding Lock ) ( $5.00 )
( 1 ) ( 28-31 Terminal Box ) ( $12.95 )
( 1 ) ( 28-31 Inside Gas Shutoff USA ) ( $39.95 )
( 2 ) ( 26-32 Slide Nuts ) ( $11.00 )
( 2 ) ( Inside Door Handle Escutcheons ) ( $11.90 )
( 1 ) ( Swing Arm Washers - set ) ( $6.95 )
( 1 ) ( 28-31 Patent Plate ) ( $3.75 )
( 1 ) ( 28-34 Door Handle Pads - set ) ( $3.00 )
( 1 ) ( A13708AC 28-29 Model A Dash Lamp Assembly ) ( $24.95 )
( 1 ) ( 28-31 15-30-15 Amp Meter ) ( $10.95 )
( 2 ) ( 26-31 Window Riser Handles ) ( $23.90 )
( 2 ) ( 26-31 Window Riser Handles ) ( $21.90 )
( 1 ) ( 28-29 Center Bumper Medallion ) ( $12.95 )
( 1 ) ( 28-31 On-Off Plate w/ SS Ring ) ( $5.50 )
( 1 ) ( 28-31 Backplate ) ( $1.75 )
( 2 ) ( Inside Door Handles ) ( $19.90 )
( 4 ) ( Door and Window Springs ) ( $2.36 )
( 2 ) ( Inside Door Handle Screws ) ( $0.90 )
( 1 ) ( Shell Lacing St/ w-rivets/ 28-29 - set ) ( $6.75 )
( 1 ) ( 28-29 Grommet set/ Radiator Shell/ Rubber/ 3 pc - set ) ( $1.75 )
Ford Model A for Sale
1931 ford model a(US $26,300.00)
1929 ford model a roadster/streetrod
1929 ford model a roadster, fully restored, very nice!(US $25,995.00)
Business coupe(US $13,000.00)
1929 ford model a 4 door murray town sedan barn fresh!! runs good!!
29 model a roadster , award winning rod and custom magazine car , supercharged(US $42,000.00)
Auto Services in Arkansas
Toyota of Fayetteville ★★★★★
Satterfield Motor Co. ★★★★★
Safelite AutoGlass - Bentonville ★★★★★
S & F Auto Sales ★★★★★
River Country Chevrolet ★★★★★
Red River Dodge Chrysler Jeep ★★★★★
Auto blog
Ford Shelby GT350 shows off HUD shift light [w/video]
Thu, Jul 23 2015We're getting pretty geeked about the upcoming Ford Shelby GT350 as Ford continues the slow trickle of news about the upcoming Mustang track beast. To review: 526 horspower, optional carbon-fiber wheels, and a wicked exhaust note from the flat-plane crank V8. And the latest piece is a programmable shift light that projects onto the windshield The head-up display, officially called Performance Shift Light Indicator, throws a line of amber lights in front of the driver's line of sight. Chevrolet uses a similar system on Camaro and Corvette models with an optional head-up display. While the GM HUD offers additional information like vehicle speed and a tachometer, the Ford system is more customizable. Depending on which of three modes, the lights flash in different patterns: Tach mode moves left to right, Track mode moves from the outside to the end until it makes a solid line, and Drag mode flashes all the light when the rpm limit is his. On the Shelby, the Performance Shift Light Indicator settings are programmed through menus in the instrument cluster's multifunction display. Stay tuned for more GT350 news next week, and check out the full press release below. View 6 Photos Ford Shelby GT350 Gets Racing-Inspired Customizable Shift Light Indicator to Help Drivers Optimize Track Time • Shelby GT350® Mustang features Performance Shift Light Indicator display with Track, Tach and Drag mode • Performance Shift Light Indicator provides the benefits of a shift light while allowing drivers to keep their eyes on the track at all times • Heads-up shift light was developed by reimagining existing hardware and is standard on all-new Shelby GT350 and Shelby® GT350R DEARBORN, Mich., July 23, 2015 – When driving the high-revving, 526-horsepower Shelby GT350® Mustang, drivers would do best to keep eyes on the road. So that's where Ford put the Performance Shift Light Indicator. For decades, race drivers have used shift lights that signal the perfect engine speed for the shift point for maximum acceleration and lower lap times during the intensity of on-track driving. Shift lights allow drivers to concentrate on the road in front of them rather than watching a tachometer. However, most shift lights either obscure the forward field of view or are located low in the instrument cluster where the driver must look down to see it. The Performance Shift Light Indicator is a heads-up display located in front of the driver.
Ford recalls 90,736 vehicles due to engine valve issue
Sun, Sep 1 2024Ford will recall 90,736 vehicles as engine intake valves in the vehicles may break while driving, the National Highway Traffic Safety Administration (NHTSA) said on Saturday. The recall impacts certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine, the NHTSA said. According to documents posted by NHTSA and sourced from the automaker, "The engine intake valves may break while driving, which can result in engine failure and a loss of drive power." Following an investigation that started in January, 2022, Ford found 22 instances where "the engine intake valves fractured and fell into the combustion chamber of the engine causing catastrophic engine damage." The automaker's analysis continues: "Ford identified that the potential root cause of the failures was engine intake valve failure due to valves that exceeded the designed specification for hardness, were brittle, and more likely to fracture. Ford determined that this was due to the supplier’s grinding processes and the sensitivity of the intake valve material to grinding processes that were not within control specifications. The intake valve material was changed for vehicles produced after October 31, 2021." Fixing the problem will require replacement of the entire engine. "Dealers will inspect each vehicle to determine its cumulative number of engine cycles. For vehicles that do not meet the engine cycle threshold, dealers will accumulate high revolutions per minute (rpm) engine cycles per a service procedure. Engines will be replaced on vehicles that do not pass the engine cycle accumulation," Ford says.
Ford reveals new rapid prototyping and low-volume production techniques [w/video]
Mon, 08 Jul 2013It's called "F3T," and that stands for Ford Free-form Fabrication Technology. The process that The Blue Oval has developed means being able to sidestep the weeks-long process of tool-and-die making when engineers want to construct a new part, allowing them to fabricate a three-dimensional part from a two-dimensional sheet of metal in just hours.
While F3T is being developed it is limited to "low-volume prototyping or even low-volume niche vehicles," but the next step is to evaluate it for use in Ford's global manufacturing facilities. You can find out more about it in the video and the press release below.