1968 Ford Galaxie 500 V8 Auto 2dr Project Car Not Running Pu Central Nj on 2040-cars
Middlesex, New Jersey, United States
|
1968 FORD GALAXIE 500
V8 302 CUI AUTOMATIC TRANSMISSION 2 DOOR NOT RUNNING, ENGINE CRANKS FINE WAS RUNNING BUT HAS BEEN SITTING PROJECT VEHICLE NEEDS WORK SOLD AS IS WHERE IS LOCATED CENTRAL NEW JERSEY, MIDDLESEX BOROUGH, ZIP 08846 VEHICLE WILL NEED TO BE TOWED/REMOVED WITHIN 14 DAYS OF AUCTIONS END $250 NON REFUNDABLE DEPOSIT DUE WITHIN 48 HOURS OF AUCTIONS END THROUGH PAYPAL(NO EXCEPTIONS) BALANCE DUE UPON PICK UP IN CASH PLEASE MESSAGE US TO COME SEE VEHICLE BEFORE AUCTIONS END VEHICLE FOR SALE LOCALLY, WE RESERVE THE RIGHT TO END AUCTION IF SOLD LOCALLY IF BIDDING REACHES RESERVE WE WILL SELL ON EBAY ONLY. ****NOTE**** WE HAVE A PENNSYLVANIA UNSIGNED/UN NOTARIZED TITLE WHICH WE ACQUIRED WHEN WE PURCHASED VEHICLE. TITLE WILL BE GIVEN TO NEW OWNER. WE DO NOT KNOW WHAT WILL NEED TO BE DONE TO GET TITLE SIGNED/NOTARIZED OVER TO YOU IF POSSIBLE ****REFRAIN FROM BIDDING IF YOU DO NOT KNOW WHAT TO DO WITH THE TITLE, WE DO NOT. TITLE HAS NO LIENS ON IT, JUST WAS NEVER SIGNED OR NOTARIZED BY PREVIOUS OWNER, THIS IS WHY WE ARE SELLING 'SALVAGE/PARTS'. MESSAGE US WITH ANY QUESTIONS |
Ford Galaxie for Sale
1964 ford galaxie base 4.7l(US $1,500.00)
1964 ford galaxie 500 xl convertible 6.4l
1966 ford galaxie 500(US $10,000.00)
1963 ford galaxie 500xl fastback rebuilt ford 429 w/ 360+hp new stage 3 c6 trans(US $16,000.00)
1963 1/2 ford galaxie 500 no engine no transmission
1969 ford galaxie 500 xl ltd convertible
Auto Services in New Jersey
Zp Auto Inc ★★★★★
World Automotive Transmissions II ★★★★★
Voorhees Auto Body ★★★★★
Vip Honda ★★★★★
Total Performance Incorporated ★★★★★
Tony`s Auto Service ★★★★★
Auto blog
Ford recalls more than 550,000 trucks and SUVs for various safety issues
Wed, Aug 12 2020Ford announced safety recalls for its current F-150 pickup along with several Ford and Lincoln crossovers early Wednesday. The recalls cover more than 550,000 vehicles and address various safety defects, ranging from a fire hazard to potential loss of braking power. The most far-reaching of the recalls covers approximately 550,000 examples of the 2015-2018 Ford Edge and 2016-2018 Lincoln MKX, which may have been assembled with defective front brake jounce hoses (also commonly referred to as "flex lines"). These hoses run from fixed points on the chassis to the individual front brake calipers. Defective hoses could potentially rupture, allowing brake fluid to leak and resulting in a loss of braking function. Ford will replace the components in question with revised parts. The next-largest recall is for roughly 3,000 2020 Lincoln Corsair crossovers. The affected models may have been assembled without proper clearance between their rear suspension springs and toe link brackets. The components could potentially make contact, wearing down the protective coating on the rear coil springs, allowing corrosion to occur over time. This corrosion could eventually lead to a failure of the spring. If this happens while the vehicle is being driven, it could result in a sudden change to the vehicle's handling characteristics, and the spring fragments could potentially cause further damage to the car or surrounding traffic. Ford says owners will be notified that their Corsairs need to be inspected; if there is not adequate clearance between the rear suspension components, Ford's service technicians will remove material from the toe link bracket to allow for operation without contact. The final (and by far the smallest) recall is for the 2020 F-150. Some units may have left the factory with the incorrect retention nut on the hot lead to the starter motor. Ford says it can cause increased heat generation or electrical arcing, which could potentially result in a fire. Ford says this issue is limited to just a few hundred examples sold in the United States. Dealers will inspect the vehicles and replace the nut if necessary.
Project Ugly Horse: Part VII
Fri, 12 Apr 2013Devils, Details and Weight Reduction
There are many things I could call this exercise. A party is not one of them.
I've spent three days crammed in the axle well of this 1989 Mustang with nothing to keep me company beyond a trouble light, a DeWalt drill on the very last of its legs and billion razor sharp, red hot slivers of metal with an affinity for my most sensitive of regions. My joints are raw from crawling around on the concrete. I'm half deaf from the shriek of the spot weld cutter and the boom of the cold chisel and hammer.
Project Ugly Horse: Part VI
Thu, 21 Mar 2013Solid axle? What solid axle?
I was fully prepared to embark on a seven-day journey down a rabbit hole of broken bolts, internet hearsay and consternation.
This should not have gone this easily. Having a long and checkered history of simple projects punctuated by much wailing and gnashing of knuckles, I was fully prepared to embark on a seven-day journey down a rabbit hole of broken bolts, internet hearsay and consternation when I finally decided to lay hands on the '89 Mustang with the goal of relieving the car of its stock rear axle. Instead, it took less than a full morning's worth of work to carve the old 7.5-inch solid axle from its moorings and mock up something, well, different.



