40 Mpg! on 2040-cars

Auto blog

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

Creations n' Chrome Top Notch Mustang is a one-of-a-kind fox

Is there a cooler car from the 1980s and early 90s to mod than a Fox-body Ford Mustang? No, there isn't. If you disagree with us, we suggest you have a look at this 1990 Mustang Coupe, which just might change your mind. Although considering just how extensively modified this car - the Top Notch Mustang from Creations n' Chrome - is, we wonder just how much Ford is left in this old pony.
It rides on a custom race tube chassis that weighs a scant 700 pounds, while carbon-fiber bits and bobs help lower the overall curb weight to a mere 2,400 pounds. When paired with supercharged, 5.0-liter, Aluminator V8 from Ford Racing, the results are, doubtlessly, exciting. 855 horsepower at the rear wheels and 667 pound-feet of torque are available from that force-fed V8 should be just plenty for this car's intended purpose of running in standing-mile competitions.
The Top Notch Mustang is more extreme than just weight savings and a big engine, though. That 5.0-liter is essentially in what's known as a front-mid layout - where the engine is actually behind the front axle. In this case, the 5.0-liter V8 is 17 inches further back than a factory Fox-body, for better weight distribution. As a result, the cabin has been completely overhauled. An SLA front suspension, wheels from HRE, Wilwood brakes and Sparco interior items round out the extensive list of mods.

Vile Gossip | Adventures in tire testing

Jean Jennings has been writing about cars for more than 30 years, after stints as a taxicab driver and as a mechanic in the Chrysler Proving Grounds Impact Lab. She was a staff writer at Car and Driver magazine, the first executive editor and former president and editor-in-chief of Automobile Magazine , the founder of the blog Jean Knows Cars and former automotive correspondent for Good Morning America . She has lifetime awards from both the Motor Press Guild and the New England Motor Press Association. This is her first column for Autoblog — look for more Vile Gossip in the future. I began writing at Car and Driver magazine back in its golden age in the 1970s, before I'd actually read it. I knew very little about cars. The only magazine I read religiously was Four Wheeler because I owned big trucks and liked to go off-roading with my Chrysler Proving Grounds friends. My vast 10 years of driving experience up to that point (high-speed dirt-road idiot, taxicab driver, Chrysler Proving Grounds test driver) had less bearing on my being hired at Car and Driver than the fact that the editor just wanted to rile up the all-male staff. He didn't need me for that. They were already in full dudgeon when I arrived. They'd just spent a chunk of time testing a stack of tires for their big tire-test issue, and the editor-in-chief was toe-to-toe with the technical editor over the rankings of the top 10 tires. It was loud, and it was angry. I had no idea that car magazines tested tires. Cab driving had led me to believe that airing up a tire and changing a flat was all you needed to know. I changed so many flats on that cab, I eventually wound up in front of a live audience on the " Oprah Winfrey Show" demonstrating my brilliance with a jack and a tire iron. My point, of course, is that tires are more controversial, and also more essential, than you'd think. My other point is that it's good to get worked up about the subject, but not quite so good to let yourself be seen, as I did, on my hands and knees with my ass up in the air on national TV. This is how I prefer to test a tire: First, pick a top brand. Then accept their invitation to try and beat the crap out of their tire. I chose Yokohama, celebrating its 100th anniversary this year. The big news for them was the GEOLANDER M/T G003!