1986 F150 Very Clean/nice on 2040-cars

Auto blog

Shelby GT350R offers first mass-produced carbon fiber wheels

In the world of race engineering, reducing total weight is good, but reducing unsprung weight is flippin' fantastic. That's the reason Ford is pushing the envelope in terms of technology for the Shelby GT350R's wheels. Joining the likes of Koenigsegg in the offering, Ford has teamed with Australian outfit Carbon Revolution to produce the CF rollers en masse for the first time. Destined for the hubs of the new Shelby GT350R, the new hoops weigh just 18 pounds each, versus the 33-lbs weight of a similar aluminum wheel. On top of slashing up to 60 pounds in unsprung weight, there's such a reduction in rotational inertia – 40 percent, versus aluminum wheels – that Ford actually has to recalibrate the magnetic ride control system and springs. Thanks to, we're guessing, scenes of crashed Formula One cars disintegrating and spewing shards of carbon fiber all over the track, Ford seems quite keen to do away with the idea that CF is strong, but brittle. The company conducted extensive shock testing, ramming a wheel into a curb at speed. According to the Blue Oval, the lightweight wheel allowed the suspension to respond so quickly that the impact was "greatly diminished," causing the tester to run the experiment again, thinking there'd been a mistake. After recording brake rotor temperatures of 900 degrees Celsius (over 1,650 degrees Fahrenheit, or well past the point that aluminum or magnesium would melt) during testing, Ford and Carbon Revolution actually redesigned the wheels to "a thermal standard more suitable for motorsports," by adding an "incredibly thin, nearly diamond-hard coating that reliably shields the resin from heat." The same process was used to protect engine turbine blades on the Space Shuttle. While the work by Ford and Carbon Revolution should make GT350R customers excited, the work being done here could have serious implications for performance cars in the future. That's the real takeaway here, and is something that should leave fans of all performance vehicles excited.

Curtain officially comes down on Mercury as dealers remove signage

The process of shutting down the Mercury is complete. Ford officially made the decision to close its mid-level brand in June of 2010. In the months that followed, Ford offered its dealers money to stop selling the cars, with production shutting down in September. The last Mercury, a Mariner, rolled off the assembly line in the beginning of October and former spokesperson Jill Wagner said her good-byes to both the car and her job. Now the last piece of the brand has come down as dealers are removing any and all Mercury signage from their lots.
[Source: Detroit News]Read | Permalink | Email this | Comments

Check out Ford's fully automated self-parking car [w/video]

As automakers continue to find uses for autonomous and semi-autonomous vehicle technology, Ford of Europe has announced that it is developing a self-parking system for future use. More advanced than the Active Park Assist already offered in many Ford products, the new Fully Assisted Parking Aid can take full control of the vehicle and can navigate angled and perpendicular parking spots.
While today's Active Park Assist can only parallel park with the driver controlling the gas, brake and gear selection, Fully Assisted Parking Aid can operate steering, gas, brake and gear selection all while making sure the car is properly parked in the intended space. As with APA, the driver pushes a button to make the car look for a proper spot (at speeds of up to 18 miles per hour), and when an adequate space is located, the operator pushes another button (either inside the car or outside via remote control) for the car to park itself - the button must be pressed throughout the whole parking maneuver. Even though Ford says that the car can effect gear selections on its own, the system must still start from Neutral, and the automaker isn't saying whether the car can put itself into Park when done or put itself in Drive when the operator is ready to go.
Ford is also taking the opportunity to announce its new Obstacle Avoidance technology. This automated system is able to detect objects - including pedestrians - in the road, warn drivers of said objects and, if needed, stop and steer automatically to avoid hitting the obstacle. Both systems are still in the prototype phase, so there is no word as to when we could see either on a production vehicle.