2004 Ford Expedition Nbx Sport Utility 4-door 5.4l on 2040-cars

Auto blog

FCA close to paying off debt, outperforming Ford in earnings

FCA boosting output of SUVs, trucks in U.S. Marchionne says the company no longer needs a merger partner FCA expects to pay off all debt this year "There's a very strong likelihood that we will outperform Ford" MILAN/DETROIT — Fiat Chrysler's shift to sell more trucks and SUVs boosted margins yet again in its North American profit center, making Chief Executive Sergio Marchionne confident he can hit most of the final targets of his five-year turnaround plan. FCA has been retooling some U.S. factories to boost output of lucrative sport-utility vehicles and trucks while ending production of some unprofitable sedans. This put the world's seventh-largest carmaker on track to become debt-free by the end of the year, and allowed Marchionne to make good on his promise to close the gap on larger U.S. rivals General Motors (GM) and Ford. "There's a very strong likelihood that we will outperform Ford in terms of operating earnings in 2018," Marchionne told analysts on an earnings call Thursday. "That's something that if I told any of us in the room here that would've been doable five years ago, nobody would have believed it." As the 65-year-old executive prepares to hand over the reins to an internal successor next year, he said the improvements mean the company no longer needed a partner to survive. The carmaker has often been the subject of merger speculation, especially after its unsuccessful 2015 attempt to tie up with GM. "The necessity to find a partner, to try and guarantee our survival, going forward, is put to bed. I mean we're done," Marchionne told analysts on a post-results conference call. North America accounted for 71 percent of earnings last quarter, and profit margins in the region rose to 8 percent from 7.1 percent a year earlier, even as shipments fell 3 percent. Meanwhile Ford's automotive margin for North America slipped to 6.8 percent, down from 8.5 percent a year earlier.FCA trimmed its expectations for 2018 revenues and forecast adjusted operating profit of at least 8.7 billion euros, at the lower end of a previously given range. Analysts said FCA's margin improvement was impressive, and it could be on the cusp of a big boost from its new Jeep Wrangler and Jeep Cherokee models and its Ram 1500 truck. FCA ready to pay off its debt But the Italian-American carmaker expects to cancel all debt during 2018 — possibly by the end of June — and generate around 4 billion euros in net cash by the end of the year.

Ford reveals EcoBoost-powered Riley prototype for Daytona 24

It's not the first time Ford has participated in the Daytona Prototype class as an engine supplier, but in revealing this new EcoBoost V6-powered Riley Technologies prototype for the new United SportsCar Championship, Ford is making a statement: "We want to show Ford EcoBoost's capabilities as an engine that provides both performance and fuel economy, on and off the track," says Jamie Allison, director of Ford Racing.
In addition to supplying the 3.5-liter twin-turbocharged V6, Ford had its production designer Garen Nicoghosian give the racecar brand-inspired design cues with support from Ford Racing chief aerodynamicist Bernie Marcus.
The car is scheduled to compete at next year's Rolex 24 at Daytona on January 25-26, but before that, Michael Shank Racing is working with Ford at another goal. Driving his Ford Thunderbird, NASCAR champion Bill Elliott set the track's top speed record at 210.364 miles per hour during a qualifying run for the Daytona 500 - way back in 1987 -- and Ford thinks it's about time for that record to fall. What better time the introduction of this new Ford-powered Daytona Prototype? Michael Shank Racing plans to use the twin-turbo V6-powered racer to beat Elliott's record, and it expects to begin prepping for the top-speed run on October 9. Scroll down for the full press release below on Ford's latest race effort.

Plug In 2014: ALTe ready to join Ford's EQVM to convert, sell F-150 PHEV [w/video]

It's been a while since we've checked in with ALTe and its plans to convert big work vehicles like the Ford F-150 into plug-in hybrids. So, when we saw a demonstration vehicle sitting outside the San Jose Convention Center at the Plug In 2014 Conference last week, we had to get a closer look. When we did, we realized that it's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. It's been quite some time since we've been in a Ride & Drive vehicle that was all beat to heck. The reason for the well-worn F-150 with 30,000 miles on it is that ALTe has been showing off its extended-range EV technology to lots of people all around the country, and Kyle Maki has been the man on the scene more often than not. "This one, I've taken all over the country," he told AutoblogGreen. "I've wore out that seat, I think. The only reason this one wasn't driven here was because we were in Charlotte [NC] last week and I didn't want to take a chance and not make it in time for this event." In other words, ALTe is out there, ginning up excitement for the idea of a plug-in hybrid Ford with an electric range of up to 40 miles and which can then continue on gas for another 360 miles at around about 25 miles per gallon. ALTe wants to not only convert new vehicles but it also offers retrofits for fleets that are happy with their current fleet. The company offers converted versions of the Ford E350 and E450 utility vehicles now but the near-mythical F-150 PHEV is still "coming soon." Yes, orders are now being accepted, but you will be forgiven if you think this is all happening on a slow time scale. There are simply a lot of things to do before ALTe can sell the truck. ALTe is currently attempting to join Ford's EQVM program, which is the electric version of the standard Qualified Vehicle Modifiers program. The QVM program requires coachbuilders to "be successfully evaluated by Ford Motor Company on criteria such as engineering, the manufacturing process, quality control, and adherence to Ford and Lincoln Divisions guidelines." Qualified applicants must also meet all applicable Federal Motor Vehicle Safety Standards, conform to Ford/Lincoln conversion guidelines and agree to be inspected annually as well as have a "commitment to continuous improvement." Maki has a simpler explanation. "It basically means you're a preferred supplier, a Tier 1, if you will," he said.