2009 Dodoge Chalenger R/t V8 Hemi Black Leather Sunroof Aftermarket Sound System on 2040-cars

Auto blog

Chrysler recalling 67k trucks with manual transmissions

Earlier this month, Chrysler announced the recall of some 280,000 pickup trucks over concerns that their axles could seize up. Now the automaker has announced an entirely separate recall of another 66,819 trucks over the springs that could break in the clutch ignition interlock switch. The recall affects Dodge Ram 1500, 2500 and 3500 pickups, as well as the Dodge Dakota and Mitsubishi Raider. The issue is relevant only to those trucks fitted with manual transmissions, from the 2006 and 2007 model years and manufactured between July 1, 2005, and July 31, 2006. Since a broken spring could, according to statements issued by the National Highway Traffic Safety Administration and FCA US LLC (previously known as the Chrysler Group) prevent the vehicle from starting, or cause it to move unintentionally once the ignition kicks over, the automaker will begin notifying owners of the affected vehicles just before Valentine's Day to bring their trucks into their local dealers to have the clutch ignition interlock switch replaced. FCA emphasizes, however, that the unintended movement would only occur "in rare cases" and only "if recommended starting procedures are not followed." Only one such case is known to have occurred, but it did regrettably result in a fatality. Statement: Clutch Ignition Interlock Switch December 29, 2014 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary global recall of an estimated 66,819 older-model pickup trucks equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. An investigation by FCA US engineers discovered switches in certain model-year 2006 and 2007 pickups may be equipped with spring wire that differs from wire used in previous switches. The alternate wire may break and, as a result, the vehicles may not start. In rare cases, a vehicle may – if recommended starting procedures are not followed – exhibit unintended movement when its ignition key is turned. The Company is aware of one fatality related to this campaign. It stemmed from the single known accident involving this population of vehicles. The recall covers certain Dodge Dakota, Dodge Ram 1500, 2500, 3500 and Mitsubishi Raider pickups. Switches with the alternate wire were not used in any vehicles produced before July of 2005, or after June of 2006. The Dakota and Raider are no longer in production.

This government surveillance van is both cool and creepy, and it could be yours

Whether you're planning a heist and need to gather information, or you're a government agency tracking down the leader of a crime ring, Hollywood has taught us that the unmarked van is the ideal machine for gathering intel. And apparently that's not just a Hollywood trope, because you can buy this actual, honest-to-goodness ex-government surveillance van: a 1998 Plymouth Grand Voyager. It's being sold by the Chicago suburb of Streamwood, Ill., on the government surplus auction site GovDeals. According to the description, the van was acquired by the town as part of a drug seizure and converted to surveillance duty. It looks like a plain white Grand Voyager for the most part, except for the amber flashing light on the roof. Or at least it looks like a light. It's actually the disguise for the camera periscope. Open up the sliding door of the van and you'll discover a swivel mount for the camera, a TV mounted to the back of the driver's seat, and a toolbox that holds all the electronic equipment, including battery chargers for the van and the camera. There are also solid panels behind the windows so that people walking by can't peer in and see all the equipment. It's a bit less wild than some of the vans we've seen on film, but those Hollywood vans are usually larger commercial vans that can store more people and stuff. Less interesting details include the fact that this Grand Voyager has a 3.3-liter V6 with an automatic transmission. It has just over 100,000 miles and was good for a little more than 150 horsepower and 200 pound-feet of torque when it was new. The interior looks impressively clean, as does most of the exterior, but the description and photos highlight the fact that the front strut towers are rusty and in need of repair. Included are new strut towers, but obviously the welding in and painting is the expensive part. Also, while we think this van is pretty neat, since it's an actual surveillance van like we've seen on film for years, we would feel creepy actually owning it. After all, it's a vehicle for watching people, and while a government might have a legitimate reason for doing that, your average person doesn't. Unless you need a prop for a film, are going to show it off at car shows, or are another city government needing a cheap surveillance car, we think having this would be a little too weird. But if you have one of those reasons, or are less worried about what people think, you have a few more days to bid.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat