2003 Chevrolet Tracker Base Sport Utility 2-door 2.0l Yellow Low Miles Look! on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

Why does the Corvette Stingray have so many vents? Here's why

Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.

Who sold the most heavy-duty pickups in 2012? PickupTrucks.com investigates

Domestic manufacturers enjoyed a good year for heavy-duty pickup sales in 2012. PickupTrucks.com has taken a close look at exactly how those sales broke down between each manufacturer and between three-quarter and one-ton pickups. Ford sold some 67,786 F-250 Super Duty models last year with the Chevrolet Silverado 2500 HD falling just behind at 56,359 units. The Ram 2500 HD came in third at 41,918, while the GMC Sierra 2500 HD earned itself fourth place with 27,616 deliveries. While Ford held onto the top spot in the one-ton market, Ram easily nailed down second place by selling more 3500 HD models last year than General Motors sold Silverado 3500 HD and Sierra 3500 HD trucks combined.
So, did GM manage to sell more trucks than Ford with its two brands? Very nearly. Ford sold a total of 119,338 heavy-duty pickups to GM's 111,555. Ram, meanwhile, moved a distant 77,583. But perhaps more interesting is the diesel take rate in this segment. PickupTrucks.com says 80 percent of all domestic one-ton trucks roll from the dealer lot with a turbo-diesel under the hood. Head over to the site for a closer look at the breakdown.