2006 Pontiac Solstice Base Convertible 2-door 2.4l on 2040-cars

Auto blog

'67 Chevy Corvair convertible vs. '86 Pontiac Fiero in cult classic showdown

Every few a decades, the folks running General Motors lose their minds briefly try to market a car that public doesn't see coming and often aren't ready for. In the '60s there was the rear-engine, air-cooled Chevrolet Corvair, then the mid-engine Pontiac Fiero in the '80s and the completely bizarre Chevy SSR in the 2000s. What all of these had in common was that they bucked the trend for American models of their era, for better or worse. The latest episode of Generation Gap tasked the hosts with finding two cult classic vehicles to choose between; they came come up with two of these quirky products from The General.
On the classic side, there's a 1967 Chevy Corvair Monza convertible. Being from later in the production run, it wears slightly more aerodynamic styling than the earlier, boxier examples. Hanging out back is an air-cooled, 2.7-liter flat-six pumping out a robust 95 horsepower. In the other corner is the somewhat more modern 1986 Pontiac Fiero SE with a mid-mounted, 2.5-liter "Iron Duke" four-cylinder, an engine nearly ubiquitous in GM cars of the '80s.
Judging by when they were new, the Corvair was far more successful than the Fiero with over 1.8 million sold. Of course, Ralph Nader's book Unsafe at Any Speed kind of poisoned the well, even if the poor safety reputation wasn't entirely deserved. The Fiero on the other hand only lasted for a few model years before shuffling off, but it eventually got its own performance boost with the V6 version and rather attractive GT models. Check them both out in the video and tell us in Comments which you want in your garage.

Trans Am Depot teases 2014 GTO

Here comes the Judge. Court is in session. The verdict is in. How many more tired clichés can we come up with? It hardly seems to matter, because it's happening: Trans Am Depot has announced via the teaser video below that it is launching a 2014 GTO, complete with Carousel Red (bright orange, really) paint and full Judge badging.
The car is based on Trans Am Depot's 6T9 Goat, which, in case you don't get the reverential references, is meant to mimic the look of the 1969 Pontiac GTO. As with the company's other cars -including the 2013 Hurst Edition Trans Am we recently drove - the GTO will be based on the current Chevy Camaro, which means two doors, V8 engines and rear-wheel drive, just like the muscle cars of days past.
As for actual details of what's under the 2014 GTO's hood, we're completely left hanging. We'd expect some sort of power adder (turbo, supercharger or possibly some other form of a highly massaged version of the Camaro's V8), and we certainly know that GM has any number of hi-po crate engines to choose from.

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...