2008 Pontiac G6 Gt Sedan 4-door 3.5l on 2040-cars

Auto blog

Camaro-based Trans Am SE Bandit Edition borrows Burt Reynolds

For some reason, modifying modern Chevrolet Camaros into the lurching, reincarnated shells of the Pontiac brand is still a thing. If you're the perverse sort that likes this kind of thing, you should check out the latest product from the Trans Am Depot, which comes complete with an endorsement from the star of Smokey and the Bandit, Burt Reynolds. Yes, the new Trans Am SE Bandit Edition has been signed and endorsed by the man himself, but what's important here is not the signature on the dash, it's the bits of Camaro that have been modified. Aesthetically, that means a Bandit-and-Frog-approved set of T-tops, a front-opening hood with a very large, prominent shaker scoop, an equally large and prominent screaming chicken, and Trans Am-inspired front and rear fascias. And naturally, Burt Reynolds' signature adorns the dash. There are plenty of reminders in the cabin about this car's Hollywood inspiration, too. Bandit decals can be found on the front headrests and center console lid, there are chicken wings on the Camaro-spec plastic door inserts, and the black-and-tan color scheme matches nicely with the exterior look. And power? Well, Sheriff Buford T. Justice would have a lot more trouble keeping up with this Trans Am than he did with the original. The 7.4-liter LSX V8 has been paired with a 2.9-liter supercharger which is good for 840 horsepower. It's fast and loud, and even if you can't get behind the look (we can't), at least this Camaro-in-Trans Am's clothing can impress with its performance. The Bandit Edition is limited to just 77 units with prices starting around $115,000. You can check out the official video from Trans Am Depot, which comes with a decent helping of Burt Reynolds, up top. Related Video:

CNN chronicles young girl building Pontiac Fiero

At fourteen years of age, Kathryn DiMaria has already done what many self-proclaimed gearheads won't even attempt in their lifetimes. The Dearborn, Michigan teen is rebuilding a car from the ground up.
The intrepid youngster asked her parents when she was just twelve to start a Pontiac Fiero project, even offering to pony up all the funds herself. Father, Jerry DiMaria only expected the project to last a few months, but two years later, Kathryn is still at it. In this CNN video, the two are at Maker Faire (a DIY festival) rebuilding a 3.4-liter V6 engine out of a Chevrolet Camaro to replace the 2.8-liter mill found in the Fiero.
The whole family hast pitched in, with Kathryn's mother teaching her how to sew in order to complete the interior, father Jerry providing much of the technical know-how, and even her sister is chronicling Kathryn's progress through photos. Jerry even started a thread in a Fiero forum which has been live for two years and is now 22 pages long. Of the project, one forum member wrote, "welcome to the madness."

Gordon Murray, F1-driven production and .. the Pontiac Fiero

Gordon Murray's design and engineering chops are unquestionable. But does his carmaking approach owe something to the short-lived Pontiac Fiero, a scrappy little car program that emerged from GM against serious resistance? Murray had a Formula One career that ran from 1969 to 1991, with stints at Brabham ('69 to '86) and McLaren ('87-'91), that resulted in several shelves' worth of trophies for the cars he was instrumental in designing. He moved on to McLaren Cars, the consumer side of things, where, during his tenure from 1991 to 2004, he helped design the McLaren F1 and the Mercedes-Benz SLR McLaren, two cars that took learnings from his two decades in Formula One. What do all of these cars have in common? Three things: They are light. They were built in limited numbers. And they were (and are) exceedingly expensive—when the McLaren F1 debuted in 1994, it stickered at $815,000. Murray went on to establish Gordon Murray Design in 2007. GMD has created some interesting concept vehicles, such as the diminutive T.25 city car (94.5 inches long, 51.1 inches wide and 55.1 inches high), and the OX, a lightweight truck for the developing world that packs like an IKEA shelf and is working toward realization through a worthy crowdfunding campaign established by the Global Vehicle Trust. Now he has created a vehicle manufacturing company, Gordon Murray Automotive, that will use manufacturing methods that he developed under the moniker "iStream." Unlike a unibody, there are the "iFrame," a cage-like construction made with metallic components, and the "iPanels," which are composite. The panels aren't simply a decorative skin; they actually provide structure to the vehicle. Presumably this has something of the F1 monocoque about it. Going back to the three elements, (1) this arrangement results in a vehicle that can be comparatively light; (2) Murray has indicated that his manufacturing company will be doing limited-run production; and (3) to launch Gordon Murray Automotive they are going to be building a flagship model, about which Murray said, "With our first new car, we will demonstrate a return to the design and engineering principles that have made the McLaren F1 such an icon." Which seems to imply that it will be on the pricey side. According to the company's verbiage, "iStream forges an entirely new production method that defies conventionality with its Formula One-derived construction and materials technologies." It also sounds a whole lot like ...