Low Mileage, Blue Beauty, Base Model, 5 Speed Manual on 2040-cars

Auto blog

GM reintroduces Tripower name in the worst way possible

The story of General Motors' use of the Tripower moniker begins way back in 1957, when Semon E. "Bunkie" Knudsen, then General Manager of GM's Pontiac division, directed his engineers to inject more performance into his brand's line of V8-powered automobiles. Fuel injection was an option, but hot rodders flocked instead to Tri-Power (marketed way back when with a hyphen), which grafted a trio of two-barrel Rochester carburetors onto a single intake manifold. A legend was born. And that legend was born of performance. At idle and when full power wasn't required, Pontiac's Tri-Power system used just the middle carburetor, which helped make the setup easier to tune. Depending on the year and model, either a vacuum system or a mechanical linkage opened up the two outer carbs, thereby switching from two barrels to six, and allowing the engine to take in more fuel and air. And it was an easy marketing win – six barrels is better than four barrels, right? Because performance! So, when news filtered in that GM has resurrected the Tripower name, those of us who grew up attending classic car shows and wrenching on old Pontiacs did a double-take. And then we all collectively sighed. Turns out that today's Tripower refers to a trio of fuel-saving measures that include cylinder deactivation, active thermal management, and intake valve lift control, according to Automotive News. And, at least for now, it applies to GM's line of fullsize trucks powered by a 2.7-liter turbocharged four-cylinder engine. We're all for saving fuel whenever possible. And we have zero say in how any automaker chooses to market its products and technologies. But, we'll offer our two cents anyway: Relaunching a storied name from the past is fine. Relaunching a storied name from the past while completely overlooking the reasons the name got famous in the first place is only going to irritate the people who remember the name in the first place. Couldn't they just call this new technology package something else? Related Video: News Source: Automotive NewsImage Credit: Getty Green Marketing/Advertising Chevrolet GM Pontiac Automotive History Truck chevrolet silverado

2020 Porsche 911 Speedster spied with an angry driver

Porsche gave us details and showed us a concept of the 911 Speedster at the Paris Motor Show. Today, we bring you spy shots of what appears to be the production version of that concept with a few changes on board. They're rather minimal modifications, but the Speedster's driver appears especially angry with our spy photographer as he extends his middle finger directly toward the camera. Sorry, not sorry, Mr. Test Driver. Public testing of pre-production cars always comes with photo risks, and Porsches tend to attract more attention than others. You'll notice what appears to be a Cayenne Coupe prototype we've previously spotted running around with the 911. The Speedster Concept we saw in Paris had epic retro mirrors and fuel cap on the front hood, but both those design touches are absent from this pre-production car. It's tougher to see, but we lost the vents in between the two humps, as well. Everything else appears to have made it to production-spec. We can't say we're surprised these concept car features probably won't show up on the production car, but it is a tad deflating. You'll notice the Speedster is based-off the 991.2 generation of 911 and not the new 992. Porsche did a similar thing when the 997 generation was coming to an end with a Speedster model paying tribute to that car's life. The chassis is said to utilize parts from the 911 GT3, and the wonderful naturally aspirated flat-six engine gets carried over from that car, too. Porsche didn't specify if power will be exactly the same as the GT3, but we'll be expecting about 500 horsepower and a 9,000 rpm redline. We were told the six-speed manual would be offered on the Speedster in Paris, too. Let's just say that we strongly approve of that combination. Production will be limited to only 1,948 cars and begin in the first half of this year. We'll expect a reveal with a full spec breakdown soon, possibly for the upcoming Geneva Motor Show. Related video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

Lutz says GM was working on 5th-gen Pontiac GTO

Bob Lutz was one of the forces behind bringing the Holden Monaro to the United States, as the ill-fated Pontiac GTO in 2004. And while that car received critical acclaim, it was a sales disappointment. Now, Road & Track is reporting that our suspicions were correct - Pontiac was working on a two-door, G8-based coupe before it was shuttered.
In that R&T article, which is no longer available online, Lutz explained that the new GTO would solve many of the issues found in the original. Car Advice speculates that the new model would have look like a rebadged version of the Holden Coupe 60 Concept from 2008, a conclusion we also came to.
That car would have been a big departure from the 2004 to 2006 GTO. It has an extremely long hood and short rear deck, with an almost fastback roofline and a wide greenhouse with a tall beltline. The wheel arches were very pronounced, and the chin and rocker panel splitters gave it a race-ready look. Would it have been enough to make the GTO work in the US? We think it might of, but it looks like we'll never know.