Red Color, Good Condition, 2 Door, 12cd Changer. on 2040-cars

Auto blog

Junkyard Gem: 2000 Pontiac Grand Prix Daytona 500 Edition

The W Platform proved to be extremely long-lived and versatile for General Motors, remaining in production from 1988 all the way through 2016. You had your Impalas and your Regals and your Cutlass Supremes, and of course the 1988-2008 Pontiac Grand Prix was a W-body. For the 2000 model year, Pontiac made the racy-looking Daytona 500 Edition Grand Prix, an example of which I just found in a Northern California self-service wrecking yard. 2,000 of these cars were made, presumably because it was the year 2000, and each one sports plenty of cool-looking Daytona 500 graphics. Perhaps some Regal owner will buy these seats and swap them. This is the second junked Daytona 500 Grand Prix I have seen recently, after this one in Colorado. The Daytona 500 was about the same as the GTP version, with Eaton-supercharged 3800 engine making a respectable 240 horsepower. Disappointingly, this car has an automatic transmission. It never saw 150,000 miles, unlike most 21st-century W-bodies I see in wrecking yards. Featured Gallery Junked 2000 Pontiac Grand Prix Daytona 500 Edition View 21 Photos Auto News Pontiac Sedan

Junkyard Gem: 1986 Pontiac Fiero GT

If you like affordable, mid-engined two-seaters, the 1980s were your decade. Fiat (and, a bit later, Bertone) offered the X1/9, Toyota sold MR2s, and even General Motors got into the act by creating the Fiero. Available from the 1984 through 1988 model years, the Pontiac Fiero showed plenty of promise but ended up being mostly disappointing, in some ways echoing the career of the Chevy Corvair of a couple of decades earlier. Today's Junkyard Gem is a once-spiffy 1986 Fiero GT, found in a self-service yard near Denver, Colorado. After a long and painful development period stretching all the way back to John DeLorean's XP-833 Banshee (which ended up being a major influence behind the original Opel GT), the Fiero finally debuted in 1983 as a 1984 model. The top-of-the-model-range GT appeared the following year. The Fiero was built as a notchback coupe and as a fastback, with all the GTs being the latter type. I couldn't get the engine lid open, but this car would have left the assembly line (in Pontiac, Michigan) with a 2.8-liter V6 rated at 140 horsepower. This car has a five-speed manual transmission, making it a credible rival for Toyota's MR2.  The 1986 MR2 was less powerful than the Fiero GT (112 horsepower versus 140), but also scaled in significantly lighter (2,459 pounds against the Pontiac's 2,780 pounds). The MR2 also cost less, priced at $11,298 while the Fiero GT cost $12,875 (that's about $30,540 and $34,805, respectively, in inflation-adjusted 2022 dollars). Meanwhile, the $6,998 Honda Civic CRX two-seater lured away many potential Fiero buyers despite being a front-engined/front-wheel-drive car, and the $7,186 Ford EXP/Mercury LN7 also put a dent in Fiero sales. I can't find a price for the 1986 Bertone X1/9, but it cost a hard-to-believe $13,990 in 1984. GM still was using five-digit odometers in many vehicles by the middle 1980s, but this Fiero has a six-digit unit and thus we can see that it nearly achieved 150,000 miles during its driving career. The 1984-1987 Fiero suffered from a parts-bin suspension design, with the front suspension borrowed from the Chevrolet Chevette and the entire rear transaxle/suspension assembly lifted from the front end of the Chevrolet Citation. For the 1988 model year, GM finally spent the money to design an improved Fiero-specific suspension … and then promptly put a halt to production.

CNN chronicles young girl building Pontiac Fiero

At fourteen years of age, Kathryn DiMaria has already done what many self-proclaimed gearheads won't even attempt in their lifetimes. The Dearborn, Michigan teen is rebuilding a car from the ground up.
The intrepid youngster asked her parents when she was just twelve to start a Pontiac Fiero project, even offering to pony up all the funds herself. Father, Jerry DiMaria only expected the project to last a few months, but two years later, Kathryn is still at it. In this CNN video, the two are at Maker Faire (a DIY festival) rebuilding a 3.4-liter V6 engine out of a Chevrolet Camaro to replace the 2.8-liter mill found in the Fiero.
The whole family hast pitched in, with Kathryn's mother teaching her how to sew in order to complete the interior, father Jerry providing much of the technical know-how, and even her sister is chronicling Kathryn's progress through photos. Jerry even started a thread in a Fiero forum which has been live for two years and is now 22 pages long. Of the project, one forum member wrote, "welcome to the madness."