2006 Mercury Mountaineer Luxury Sport Utility 4-door 4.0l on 2040-cars

Auto blog

NHTSA investigating 500k Ford and Mercury cars for lighting failures

The Ford Crown Victoria and Mercury Grand Marquis might be long gone as new models in showrooms, but the National Highway Traffic Safety Administration might check them out yet again for a potential problem. At the urging of North Carolina Consumers Council, the agency may open another investigation into the front lighting control module on vehicles from the 2003-2005 model years, and NHTSA estimates the issue could affect 517,945 vehicles. If the module stops working, it can cause a complete failure of all forward lighting, including the headlights. NHTSA previously investigated the issue in 2008 and 2009 but found no need for a recall, according to Bloomberg. Ford also extended the warranty on the part to 15 years or 250,000 miles. To prompt this new request, the North Carolina Consumers Council received a letter from a woman experiencing the module's failure. Upon further investigation, the council found 604 complaints of this problem on NHTSA's website, including seven crashes. Furthermore, the group has alleged that dealers told customers that the parts to perform the replacement weren't available, despite the extended warranty. According to the government agency, "A defect petition has been opened to evaluate the issue and make a grant or deny decision." Ford spokesperson Kelli Felker tells Autoblog via email, "We will cooperate with NHTSA, as we always do." You can read the council's complete letter to the Feds in PDF format, here. INVESTIGATION Subject : Loss of headlamp/exterior lighting Date Investigation Opened: APR 01, 2015 Date Investigation Closed: Open NHTSA Action Number: DP15002 Component(s): EXTERIOR LIGHTING All Products Associated with this Investigation Vehicle Make Model Model Year(s) FORD CROWN VICTORIA 2003-2005 MERCURY GRAND MARQUIS 2003-2005 Details Manufacturer: Ford Motor Company SUMMARY: The Office of Defects Investigation (ODI) has received a petition from the North Carolina Consumers Council, Inc. requesting a defect investigation of an alleged defect condition resulting in headlight and/or exterior lighting failure on 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles. The petition letter is attached for review. The petitioner alleges a defect in the lighting control module that powers the headlights which can result in the loss of vehicle headlights and/or all exterior lighting while driving. ODI has previously investigated this issue under PE08-066 which was closed without a defect finding.

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: