2dr Conv Ls Manual Mazda Mx-5 Miata Ls Convertible Manual Gasoline 1.8l Dohc Mfi on 2040-cars

Auto blog

The redesigned 2019 Mazda3 moves way upscale

Mazda didn't lie — the 2019 Mazda3 is a gently reworked production version of the Kai concept shown at last year's Tokyo Auto Show. In hatchback and sedan forms, you'll still quickly peg this a Mazda3. The dimensions barely change: The wheelbase grows by an inch, but the hatchback width and length carry over, while height decreases by an inch; the sedan is the same width but 3.2 inches longer and 0.7 inches lower. Nevertheless, the look and details have evolved throughout, yielding a much more potent and piercing hatchback, and a more sophisticated, accomplished sedan. Instead of using hard shoulder and swage lines to "draw" contour onto a flat profile, Mazda designed a car with contours that create real shoulders and hips. Shedding the illusion of surface depth for reality redefines the look and presence of the Mazda3. The new model erases the hash of lines and embossed panels in back of the current car so that the S-curved hatch has only its shutline for framing. After that, the highlights enhance the theme. On either side of the larger grille, single-lens headlamps get new accents; instead of a just plain silver bar, streaks of amber turn signals decorate the more dimensional units. The contoured taillamp housing holds highly structured, highly embellished twin circles that probably look even more sinister at night. On the sedan, those naughty taillights are surrounded by a refined rear valance with a more angled, muscular lip along the trailing edge. It's the same inside, a design based on results of Mazda's in-depth studies of human mechanics. The flatter instrument panel stresses clean lines along the horizontal. Trimmer steering wheel spokes with silver buttons line up with the central span across the dash housing the climate control buttons and vents. The new shift panel sits higher and more forward, making it easier for the driver to move a hand from the steering wheel to the lever. To raise perceived luxury, the center tunnel trim is a clear layer laid over a laser-engraved black layer, said to produce a "look of deep transparency," and similar to the effect found on the new BMW X5 and X7. The cupholders are now in front of the shifters, and the armrest is longer. There's no mention of that digital gauge cluster that leaked earlier this year, though. Buyers who opt for fabric will get a new "Greige" hue, a mix of gray and beige. Mazda designed a new leather grain with creases of varying depths and shapes depending on where it's placed.

2019 Mazda 3 recalled because the wheels could fall off while driving

Here’s a recall we had to read twice before believing. Mazda is bringing in 25,003 Mazda 3s that just rolled off the assembly line, because the wheels may fall off while driving. All the Mazda 3s are 2019 model year cars, so itÂ’s only the totally new generation Mazda 3 under the gun here. Thankfully, Mazda says there are no cases of this occurring to owners, and therefore no injuries or deaths related to the issue. As for the cause of the wheel detachment? Mazda put out a statement explaining the issue at hand.  “A manufacturing process error may result in a gap between the wheel hub bolt and hub flange during assembly. This gap causes loosening of the lug nuts though they were initially tightened to the correct specification at the plant. A rattling noise occurs prior to a wheel detachment from the vehicle,” Mazda says. ItÂ’s heartening to see Mazda did in fact tighten the lugs at the factory, but still extremely troubling to see that they can loosen all on their own. Our advice? Walk on out to your shiny, new Mazda 3 and torque those lugs to spec. If you donÂ’t have a torque wrench, then just use the wrench that came with the car to make sure theyÂ’re not loose. Those that have a new Mazda 3 should be on the lookout for a recall notice in the mail. YouÂ’ll then be able to take the car to the dealer for Mazda to fix the problem. Until then, just keep an eye on your lugs. A wheel flying off while driving at speed is always a recipe for disaster, and we sure do enjoy driving the new Mazda 3 at speed.

Mazda details diesel prototype at Daytona test

Diesel has without a doubt become the dominant fuel in the modern era of endurance racing. The 24 Hours of Le Mans has been won under diesel power for the past eight years running, as has every race in the FIA World Endurance Championship since its inauguration in 2012. Yet there will only be one diesel prototype entered in the top tier of the new Tudor United SportsCar Championship this year, and it belongs to Mazda.
The last Japanese manufacturer to win at Le Mans outright, Mazda has been gradually working its way back up the endurance racing ladder once again, following the example set by Audi with diesel power. Last year it campaigned a competition-spec Mazda6 Skyactiv-D in the GX class of the Grand-Am series, but rather than simply port over the existing racer into the new series, it's fielding a new prototype instead, just as it promised a couple of months ago. And now that prototype has hit the track for the first time, prompting Mazda to release its basic specs for the first time.
Tentatively referred to simply as the 2014 Mazda Prototype, the purpose-built racecar is testing this weekend in the Roar Before the 24, the official test session at Daytona that kicks off the racing season. It packs a 2.2-liter SkyActiv-D engine that's based heavily on the production version but tuned to produce 450 horsepower and 580 pound-feet of torque in race trim. Power is channeled through a six-speed sequential transmission from Xtrac, carbon brakes from AP and 18-inch racing slicks from Continental. With the Daytona-spec aero setup, it'll top out at around 186 miles per hour.