12 Es350 V6 Sunroof Heated Cooled Leather Bluetooth Park Assist Wood Trim Alloys on 2040-cars

Auto blog

Toyota to enter modern turbo four-cylinder era with Lexus crossover

Toyota has sat quietly on the sidelines as many of its competitors have armed themselves in recent years with lower-displacement turbocharged four-cylinder engines in an effort to gain better fuel efficiency numbers and flatter power curves. It's a strategy largely shared by fellow countryman Honda, who turned away from offering forced-induction four-cylinder models in North America after its first-generation Acura RDX failed to find buyers. Toyota itself has no lack of experience with turbo fours, having built some humdingers for cars like the MR2 and Celica All-Trac back in the 80s and 90s. It's also offered factory-warranted turbos through its TRD performance parts division more recently.
Now, Automotive News is reporting that the world's largest automaker is finally poised to rejoin the turbo-four production-car fray in North America, but it won't be a sports car that delivers the first force-fed punch, it will be a new small crossover model for Lexus. We first showed you spy shots of the NX last week in mule form, and Automotive News says the small softroader will carry a 2.0-liter turbo four in its engine bay when it rolls on to world markets in 2014 or early 2015. That model, the NX 200t, will be joined by the NX 300h, a hybrid variant. It isn't immediately clear when US buyers will see the turbo model, however, it's possible that the hybrid could bow first - the story quotes an anonymous company source suggesting that Americans might not see the engine offering until sometime in 2015.
AN further posits that the new 2.0-liter will likely supplant the company's 2.5-liter V6 in the IS sedan and the same-displacement four-cylinder in the Toyota RAV4, but does not indicate where the new engine will be built.

Why is there a huge bulge in 2021 Lexus IS 300 AWD's driver footwell? We explain

After an initial turn a few weeks ago for the 2021 Lexus IS first drive review, the revised luxury sedan has returned to the Autoblog garage for a second look. This middle-of-the-road IS 300 AWD pairs a 260-horsepower V6 with a six-speed automatic transmission and four driven wheels, and frankly it's the least interesting way to spec out the redesigned sedan. While there are cars in this segment designed to get a performance boost from their all-wheel-drive systems even in dry conditions, the IS isn't one of them. Adding insult to injury, you get stuck with a cramped driver-side footwell care of the engineering shenanigans that went into making this system possible.  While we've mentioned this particular compromise before, we rarely touch on the reasons why it exists in the first place. The fundamentals are fairly obvious; the standard IS utilizes a longitudinal, rear-wheel-drive powertrain. As is typical with this configuration, the transmission sits in a tunnel beneath the center console. This arrangement works just fine, provided you don't need to power the front wheels.  To do so in a traditional car like the IS requires a literal end-around maneuver involving the engine and transmission, which we've diagrammed for you below care of MSPaint. This is a bit simplified for the sake of this write-up, and it should be noted that this is not the only way to implement AWD in an inherently RWD platform, but it illustrates how the power for the front axle (red) and rear axle (blue) flows from the transmission to the drive wheels. To get juice flowing to the front axle, Lexus had to add a parallel output shaft, exiting the transmission from the front with enough clearance for the bell housing and engine, which sits between the transmission and the front differential. This requires quite a bit of lateral reach, meaning the housing has to extend much farther out than usual to accommodate it (yellow arrow). As a result, the all-wheel-drive transmission looks a lot like a sci-fi gun with a chunky drum magazine hanging off the side of it. The hump (above right) in the footwell is there to clear this protrusion. This basic configuration isn't unique to Lexus. In fact, if you look at a BMW xDrive cutaway, it's similar. So, why no "hump" in other cars? There are multiple factors, but to boil it down to what is most relevant, it's a combination of the resulting shape of the Lexus transmission housing and the size of the IS chassis.

Toyota offered $146.5 million to build Lexus ES in Kentucky

Toyota posted a media advisory yesterday saying that Akio Toyoda, president of Toyota, and Jim Lentz, CEO of Toyota North America, would be making a production announcement tomorrow in New York City, and Automotive News reports that the automaker will be announcing a plan to domestically produce the Lexus ES. According to the report, numerous plants are competing to build the ES in North America, and the State of Kentucky has offered the automaker up to $146.5 million to build the luxury sedan at the Georgetown, KY assembly plant.
If Georgetown gets the ES, which has been built in Japan since its debut in 1989, it would be built alongside the Toyota Camry, which is somewhat ironic since in our review of the 2013 Lexus ES350, we wrote that this ES finally says "goodbye to its Camry roots." In order to get the whole amount offered, the article states that Toyota would have to invest $531.2 million and hire 570 full-time workers at the plant, which doesn't sound all that unreasonable since the plant would require an additional 50,000 units of annual production, not to mention the fact that the Georgetown facility is already at its capacity for building the Camry.