2013 Infiniti Ex37 Awd Journey Premium Package on 2040-cars

Auto blog

Infiniti Prototype 9 is a wonderfully beautiful EV grand prix car

Few automobiles are as elegantly beautiful as the open-wheel grand prix cars of the 1940s, '50s and '60s. The simple, slender shapes of these cars bear no extravagant flourishes or adornments. The purposeful design is what gave these cars their beauty, and it's these classic machines that inspired the new Infiniti Prototype 9. Teased earlier this week, this concept blends old and new, with classic lines hiding a modern all-electric powertrain. The Prototype 9 will make its full debut next week at the 2017 Pebble Beach Concours d'Elegance. Infiniti says the car was built around a simple idea: what would a 1940s Infiniti grand prix car look like? While the silver paint may be more German than Japanese, the design could easily be mistaken for an actual '40s grand prix car. Only the Infiniti-styled grille gives it away. Everything about it, from the thin bias-ply tires wrapped over center-locking wire wheels to the bulging screws around the driver's seat, is pitch perfect. Underneath that achingly long hood rests a prototype electric motor and battery from Nissan's Advanced Powertrain Department. The combo sends 148 horsepower and 236 pound-feet of torque straight to the rear wheels. That's good enough to send the svelte 1,962 lb car to 62 mph in just 5.5 seconds. Top speed is right at 106 mph. While speed may die off towards the top end, all that torque and a 43/57 front to rear weight distribution should make the Prototype 9 a riot on a small, tight circuit. There's only enough juice in the battery for about 20 minutes of flat-out racing. The handmade steel body rests on a steel ladder-frame chassis. The front suspension uses a leading-arm rigid axle with transverse leaf spring while the rear uses a De Dion axle, also with a transverse leaf spring. The Prototype 9 also uses old-school hydraulic rotary type dampers. There's no power steering and no brake booster for the four-wheel disc brakes. The car was designed and built by a number of different departments within Infiniti and Nissan. A simple sketch expanded as more and more designers and engineers wanted to have a hand in the project. The steel body panels were all shaped and hammered by hand. The bare cockpit is only adorned with a thin seat, three gauges, a few switches, a gear selector and the steering wheel. The gauges are set into a fixed aluminum hub in the center of the steering wheel.

Infiniti-Red Bull Racing will seek a fourth title with the RB9 [w/video]

This is the car and the team that everyone wants to dethrone. The stability of this year's regulations means that the Infiniti Red Bull RB9 is a seriously honed RB8; however, that's a situation probably no other team would complain about seeing that the RB8 recovered from early stumbles and reliability issues last year to carry Sebastian Vettel to a third consecutive driver's title and the team to a third consecutive constructor's trophy.
The most noteworthy revisions to the car are the partial vanity panel that omits the driver cooling slot, the even narrower rear end - a feature of just about every car launched so far - and purple sidepods to showcase new title sponsor Infiniti. Adrian Newey, perhaps the most feared designer on the pit lane, said the nose and front wing could be changed relatively easily throughout the season, but he wanted to make sure to get the middle of the car - everything from the sidepods, back - as good as possible since they're more difficult to re-engineer. His track record leads us to believe he did just that.
Below are two videos, one of the making of the RB9, the other the launch at team headquarters in Milton Keynes.

Nissan recalls Rogue, Pathfinder, Infiniti QX60 for seat issue

Nissan and Infiniti are recalling their 2023 Rogue, Pathfinder and QX60 SUVs and CUVs to address a potential defect in their seat frame welds that can allow the frames to fail in the event of a collision. The number of vehicles that potentially shipped with weak welds is rather small — just over 12,000 — but the issue could nonetheless lead to injury if a failure occurs during a collision.  "The driverÂ’s powered seat may not be fully secured to the seat frame on certain Nissan Rogue, Pathfinder, and INFINTI QX60 vehicles," Nissan's report to NHTSA said. "As a result of this issue, the seat frame welds may detach from the rear inboard seat bracket. If this condition occurs, it may increase the risk of injury to the occupant in the event of a crash. In addition, the seat frame assembly may not meet certain FMVSS 207 and FMVSS 210 requirements because of this condition," Nissan said.  Nissan says there's no easy way for customers to detect the issue ahead of time, and that its seats need to be inspected by a service tech to see whether it is properly secured. Dealers will be instructed to check the driverÂ’s seat rail clearance to the inboard seat bracket, and if necessary, the dealer will remove and replace the affected driverÂ’s seat cushion frame, NIssan said. The entire procedure should take less than two hours.  Owners of affected vehicles should look for notices to be delivered no later than June.  Related video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Recalls Infiniti Nissan Crossover SUV Luxury