1929 Ford Model A Faux Roadster Pickup W/ 39 Trans & Hydraulic Brake Conversion on 2040-cars

Auto blog

Ford recalls over 953,000 vehicles to replace Takata airbag inflators

DETROIT — Ford is recalling more than 953,000 vehicles worldwide to replace Takata passenger airbag inflators that can explode and hurl shrapnel. The move includes over 782,000 vehicles in the U.S. and is part of the largest series of recalls in U.S. history. Included are the 2010 Ford Edge and Lincoln MKX, the 2010 and 2011 Ford Ranger, the 2010 to 2012 Ford Fusion and Lincoln MKZ, the 2010 and 2011 Mercury Milan, and the 2010 to 2014 Ford Mustang. Some of the recalls may be limited to specific geographic areas of the U.S. Takata used the chemical ammonium nitrate to create an explosion to inflate airbags. But it can deteriorate over time due to heat and humidity and explode with too much force, blowing apart a metal canister designed to contain the explosion. At least 23 people have been killed worldwide and hundreds injured by the inflators. Ford says it doesn't know of any injuries in vehicles included in this recall. Dealers will replace the inflators. Ford will notify owners about the recall starting on Feb. 18, and the company has replacement parts available for dealers to order, said spokeswoman Monique Brentley. In previous Takata recalls, parts availability had been an issue. Owners can go to this Ford website and key in their vehicle identification number to see if their cars and SUVs are being recalled. The same information will be available soon at the NHTSA recall website. More than three years after the U.S. National Highway Traffic Safety Administration took over management of recalls involving Takata inflators, one third of the recalled inflators still have not been replaced, according to an annual report from the government and a court-appointed monitor. The report says 16.7 million faulty inflators out of 50 million under recall have yet to be replaced. And 10 million more inflators are scheduled to be recalled this month, including the Ford vehicles. Safety advocates said the completion rate should be far higher given the danger associated with the inflators. The recalls forced Takata of Japan to seek bankruptcy protection and sell most of its assets to pay for the fixes. The inflators grow more dangerous as they get older because ammonium nitrate deteriorates due to high humidity and cycles from hot temperatures to cold. The most dangerous inflators are in areas of the South along the Gulf of Mexico that have high humidity. Related Video:

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.