1996 Ford Taurus Lx Wagon Runs Good Clean No Reserve Cheap Decent Ride on 2040-cars

Auto blog

F-150 just the start of Ford's aluminum plans

Not only have we been told that the 2015 Ford F-150 is tougher, more durable and up to 700 pounds lighter than the current truck, Ford COO Mark Fields said it's also "CAFE-positive." That means, for the first time in the history of corporate average fuel economy standards, the F-150 would be a positive contributor on Ford's CAFE balance sheet instead of being a vehicle it needs to counterbalance with frugal offerings.
Fields' comments made at the Detroit Auto Show were among quotes from other Ford execs that confirmed the carmaker will be using aluminum for more of its vehicles. CEO Alan Mulally said it would "proliferate across our lineup," with speculation being that we'll see it applied to crossover and sport utility models first, since they'll benefit the most. Even gaining the massive scale of using aluminum on the world's best selling vehicle for its first effort - on average, the company sells two times as many F-150s in a single day as Land Rover sells of its aluminum Range Rover in a month - Ford will be looking to further spread the cost of its five-year development investment in aluminum technology. And that should mean better handling and fuel economy for those of us who don't need to wear hardhats at the office.

Ford issues six recalls covering 101,000 vehicles for multiple issues

Ford is announcing six separate recalls for a variety of issues affecting a dozen models and a total of 100,610 vehicles in North America. However, according to Ford spokesperson Kelli Felker, "None of them have caused accidents or injuries." Half of them cover fewer than 1,000 cars.
The largest recall covers 92,022 North American examples (about 83,250 in the US) of some models of the Ford Taurus, Lincoln MKS, Ford Interceptor, Flex and Lincoln MKT from the 2013 and 2014 model years; the 2012-2014 Edge and the 2014 Lincoln MKX. All of them have a potential issue with the halfshaft on the right side that might not be fully seated and could move outward over time. If it shifts too far, the models may no longer be able to drive, and the condition could also allow the vehicles to roll away, even when in Park. Dealers will inspect the shaft to make sure it's seated and will replace the part if necessary.
The next-largest recall covers 5,264 North American examples (4,867 in the US) of the Ford F59 Commercial Stripped Chassis from the 2011-2014 model years. It's possible that an electrical junction box can corrode in areas with salty roads and short circuit. The problem could potentially cause a fire. Dealers will replace the box with an improved design.

MotorWeek relives '80s coupes with Dodge Daytona, Ford Escort EXP

Get ready for a wave of nostalgia and the rapid realization of the huge progress in performance cars over the last 30 years. For its latest Retro Review, MotorWeek takes a look back at two, front-wheel drive coupes from the '80s that seem to have entirely vanished from the roads today. Both the 1986 Dodge Daytona CS and the 1986.5 Ford Escort EXP were considered affordable, sporty options in their day, but the passage of time hasn't been kind to either of their specs. The Daytona certainly looks the part of a performance machine with a body that's reminiscent of other '80s coupes, like the third-gen Chevrolet Camaro. However with 146 horsepower and 170 pound-feet of torque from a 2.2-liter turbocharged four-cylinder, acceleration wasn't exactly a strong suit. MotorWeek complained about copious torque steer, as well. The optional CS suspension upgrade package on this Daytona was apparently a nod to Carroll Shelby who was working with Dodge at the time. If anything, the Escort EXP withstands the test of time even worse. As a two-seat coupe, you might have expected Ford's engineers to really turn up the performance to fit the sporty image that the exterior conveyed. That didn't really happen, and depending on which model buyers ordered, they got either 86 horsepower with a 1.9-liter engine or the "high-output" version of that mill with 108 hp.