2008 Ford F-450 Super Duty Xl Crew Cab Pickup 4-door 6.4l on 2040-cars

Auto blog

2015 Ford Mustang already under recall, but just 53 units

Ford has issued a small - but significant - recall for one of its spotlight cars: the 2015 Mustang.
The recall affects just 53 cars, with 50 in the United States and three in Canada. Ford said the passenger side safety belt buckle tension sensor may not have been calibrated properly by the supplier. This could lead to "misclassification" of the passenger seat occupant, and could cause the airbag to deploy improperly.
A Ford spokesperson didn't immediately respond to a request for comment. In a statement, the automaker said it is not aware of any accidents or injuries, and dealers will replace the buckle assembly at no cost to customers. The cars affected were built at Flat Rock Assembly Plant in Michigan from Aug. 18 to Oct. 2.

Creations n' Chrome Top Notch Mustang is a one-of-a-kind fox

Is there a cooler car from the 1980s and early 90s to mod than a Fox-body Ford Mustang? No, there isn't. If you disagree with us, we suggest you have a look at this 1990 Mustang Coupe, which just might change your mind. Although considering just how extensively modified this car - the Top Notch Mustang from Creations n' Chrome - is, we wonder just how much Ford is left in this old pony.
It rides on a custom race tube chassis that weighs a scant 700 pounds, while carbon-fiber bits and bobs help lower the overall curb weight to a mere 2,400 pounds. When paired with supercharged, 5.0-liter, Aluminator V8 from Ford Racing, the results are, doubtlessly, exciting. 855 horsepower at the rear wheels and 667 pound-feet of torque are available from that force-fed V8 should be just plenty for this car's intended purpose of running in standing-mile competitions.
The Top Notch Mustang is more extreme than just weight savings and a big engine, though. That 5.0-liter is essentially in what's known as a front-mid layout - where the engine is actually behind the front axle. In this case, the 5.0-liter V8 is 17 inches further back than a factory Fox-body, for better weight distribution. As a result, the cabin has been completely overhauled. An SLA front suspension, wheels from HRE, Wilwood brakes and Sparco interior items round out the extensive list of mods.

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.