2010 Ford Edge Limited on 2040-cars
Little Rock, Arkansas, United States
For Sale By:Dealer
Engine:3.5L 3496CC 213Cu. In. V6 GAS DOHC Naturally Aspirated
Body Type:Sport Utility
Transmission:Automatic
Fuel Type:GAS
Cab Type (For Trucks Only): Other
Make: Ford
Warranty: Vehicle does NOT have an existing warranty
Model: Edge
Trim: Limited Sport Utility 4-Door
Disability Equipped: No
Drive Type: FWD
Doors: 4
Mileage: 45,822
Drive Train: Front Wheel Drive
Sub Model: Limited
Number of Doors: 4
Exterior Color: Other
Interior Color: Other
Number of Cylinders: 6
Ford Edge for Sale
2013 ford edge heated leather back up camera chrome sony history report 11 12(US $28,990.00)
2007 ford edge sel fwd(US $10,479.00)
Sel fwd suv 3.5l (2) coat hooks (2) rear grab handles (6) cup/bottle holders(US $15,377.00)
White suv clean title finance moonroof leather power awd air auto power stereo
2012 ford edge sport certified pre owned
Repairable rebuildable salvage wrecked nice project runs loaded navigation save(US $15,900.00)
Auto Services in Arkansas
West End Garage Inc ★★★★★
VIP Auto Body & Collision ★★★★★
Ultimate Auto Sales ★★★★★
Trans Tech ★★★★★
Russell`s Truck Accessories ★★★★★
Performance Cars & Trucks ★★★★★
Auto blog
Ford recalls 90,736 vehicles due to engine valve issue
Sun, Sep 1 2024Ford will recall 90,736 vehicles as engine intake valves in the vehicles may break while driving, the National Highway Traffic Safety Administration (NHTSA) said on Saturday. The recall impacts certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine, the NHTSA said. According to documents posted by NHTSA and sourced from the automaker, "The engine intake valves may break while driving, which can result in engine failure and a loss of drive power." Following an investigation that started in January, 2022, Ford found 22 instances where "the engine intake valves fractured and fell into the combustion chamber of the engine causing catastrophic engine damage." The automaker's analysis continues: "Ford identified that the potential root cause of the failures was engine intake valve failure due to valves that exceeded the designed specification for hardness, were brittle, and more likely to fracture. Ford determined that this was due to the supplier’s grinding processes and the sensitivity of the intake valve material to grinding processes that were not within control specifications. The intake valve material was changed for vehicles produced after October 31, 2021." Fixing the problem will require replacement of the entire engine. "Dealers will inspect each vehicle to determine its cumulative number of engine cycles. For vehicles that do not meet the engine cycle threshold, dealers will accumulate high revolutions per minute (rpm) engine cycles per a service procedure. Engines will be replaced on vehicles that do not pass the engine cycle accumulation," Ford says.
Auto critic calls out Corvette, Mustang and Cherokee faithful
Mon, 26 Aug 2013Most automotive purists fear change, but not without reason. Change, after all, did kill big-block V8s, along with most station wagons and manual transmissions. But change has also brought with it far more performance, safety and fuel economy - not to mention ridding the world of shag carpet interiors, bias-ply tires and those horrible motorized seatbelts of the early '90s.
By this time next year, the Chevy Corvette, Jeep Cherokee and next-generation Ford Mustang will all be on sale and will all, in some way, have angered or offended purists. To those critics, Mark Phelan of the Detroit Free Press is preemptively telling them to stop complaining - at least until they've all been driven. From the Corvette's square taillights and the Cherokee's radical nose to whatever pony car purists will harp on the 2015 Mustang for, Phelan's column points out the positives of automotive evolution and the negatives of staying the course for too long. That's fair enough, but do you think Phelan is on point, or all wet? Head on over to the Detroit Free Press to read his words, then have your say in Comments.
Trump to meet with CEOs from Ford, GM, and FCA
Tue, Jan 24 2017In the wake of his inauguration, President Donald Trump is set to meet with the CEOs of Ford, General Motors, and Fiat Chrysler Automobiles Tuesday morning to discuss jobs, the North American Free Trade Agreement, and potential tax cuts. Trump has been highly critical of American automakers for shipping jobs to Mexico and has threatened to impose heavy import fees on foreign-made vehicles. Trump has threatened to dissolve NAFTA in order to encourage automakers to manufacture cars in the US. Automotive News and Crain's Detroit Business are reporting that the group is set to discuss how to bring more auto industry jobs back to the US. Under NAFTA, many automakers, both foreign and domestic, have moved vehicle production out of the States to Mexico in order to cut costs. White House spokesperson Sean Spicer said Trump is looking forward to the meeting and discussing how to bring jobs back to America. Dismantling NAFTA would be a major blow to automakers. Trump blasted Ford during his campaign for manufacturing in Mexico, but FCA and GM also have factories south of the border. Earlier this month, Ford nixed plans for a $1.6 billion plant in Mexico, instead investing $700 million into an existing facility. At this year's Detroit Auto Show, the unspoken theme was America and American manufacturing. Expect the automakers to fight to keep NAFTA alive. Related Video: News Source: Automotive News - sub. req., Twitter Government/Legal Plants/Manufacturing Fiat Ford GM FCA Mexico NAFTA
