2010 Ford Econoline E250 With Mobility Works Power Wheel Chair Lift on 2040-cars

Auto blog

A cool boost to turbocharger performance

Since the advent of the forced-induction engine, we have been looking for ways to get every drop of performance we can. There are many approaches to getting additional power using better intercooling, water injection, or even adding nitrous oxide. One take on a short instant burst of power is being researched by Mahle and involves providing supercooled air to an engine, which allows it to burn a leaner fuel mixture and produce more power. The supercooling idea is not new and was examined by Ford in 1993 on the Mustang Mach III concept car, then brought up again in 2003 with the SVT F-150 Lightning concept. Ford called its system the SuperCooler; it was designed to work with any turbocharged or supercharged engine equipped with a water-to-air intercooler. The system on the Lightning concept used a small tank of antifreeze that was hooked up to the truck air conditioning compressor. The air conditioning compressor cooled the antifreeze down to about 30 degrees. The other side of the tank was hooked up to the air-to-water intercooler, which usually had a temperature over 100 degrees. Once the antifreeze was circulated from the tank into the intercooler, it would lower the intercooler temperature and provide for a cooler, denser air charge into the engine; the result was around 50 extra horsepower for a burst of about 30 seconds to a minute, depending on the size of the tank. The system for the Lightning was to be offered as a $750 option and would have been targeted towards drag racers and the like, as it could be used for a run down the drag strip and then re-cooled by the time the truck was back in line. The system was fairly non-intrusive – it only weighed about 25 pounds and did not require a new compressor or intercooler. But as with many concepts, it was ultimately scrapped. The technology was always stuck in the back of my mind, but with larger and more powerful engines being produced it could not find its place. With the advent of new fuel economy standards, we have seen small-displacement turbocharged engines pop up and they seem like the perfect candidate for this type of technology. Ford's EcoBoost 1.0-liter three-cylinder turbocharged engine, as used in the Fiesta and Focus, is one such candidate for this technology. It would add a negligent amount of weight but could provide a boost of 10 to 20 horsepower when needed, like merging onto the highway or catching up to traffic.

2015 Ford F-150's aluminum body not expected to hurt resale value

A cloud of skepticism has hung over the 2015 Ford F-150 since even before it went on sale. The issue had nothing to do with the truck's capabilities but instead over reservations about the switch to aluminum body panels. The change helped shed about 700 pounds off the scales, but the lighter metal also came with the potential for higher repair costs. Edmunds even recently whacked its pickup with a hammer just to find out how much it would cost. However, this might not be a problem, because the latest calculations indicate resale value for the new F-150 is on the rise. The residual experts at ALG estimate that the 2015 F-150 is going to hold 58 percent of its value over the next three years, versus 52 percent for the 2014 model, according to Bloomberg. That figure also gives the Ford the highest forecasted resale value among American fullsize pickups. The 2015 Toyota Tundra leads the segment by holding 63 percent. Meanwhile, the 2015 Chevrolet Silverado and GMC Sierra both come in with 51 percent, and the Ram 1500 holds 46 percent. Finally, the 2015 Nissan Titan comes in at 42 percent. The researchers believe that the improvement in fuel economy for the 2015 F-150 at up to 26 miles per gallon highway offsets higher body repair costs. "We are giving credit for the aluminum construction in the fuel efficiency we're seeing," Eric Lyman, ALG vice president of industry insights, said to Bloomberg. "We are not putting in a negative adjustment for concerns around repair costs or durability associated with aluminum." Ford has long-been preparing for the switch to aluminum. The company purposefully designed the body sections to make repairs easier, and it also partially subsidized dealers' investments for new equipment to do the work. Related Video:

Martini Mustang is a 'what if moment' gone right

Feast your eyes on a masterpiece. This is Steve Strope's Ford Mustang in the classic fastback bodystyle, and as you'll notice, it sports the signature colors of Martini Racing, a livery that's as legendary as any Gulf Racing-styled car. But the red, white and blues of the Martini stripe down this Mustang's middle tell only a very small part of the story, in the latest video from Petrolicious.
What would you guess is under the hood? A 289-cubic-inch V8? Maybe a 302, or some absurd Ford crate engine? Maybe Strope went all Tokyo Drift - he's actually responsible for the "Hammer" Plymouth Satellite driven by Vin Diesel at the end of the movie - and found an RB26DETT to drop into the pony car? You'd be wrong on all counts.
This mad, mad man somehow finagled a Ford-Lotus engine from a 1966 Indianapolis 500 car into the Mustang's engine bay. Yes, a Mustang with an engine designed for a 160-mile-per-hour, open-wheel racecar. That's like someone in 40 years dropping McLaren's 2.4-liter V8 from the MP4-28 into a Scion FR-S. It'd just make a monster.