2014 Dodge Journey Se on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

These cars are headed to the Great Crusher In The Sky

It happens every year. We bid adieu to some cars and trucks that will be missed, and say good riddance to others wondering how they stayed around so long. Whether they're being killed off for slow sales or due to a new product coming along to replace them, the list of vehicles being discontinued after 2012 is surprisingly long and diverse.
CNN Money has compiled a list of departing vehicles, to which we've added a few more of our own. In the slow sales column, cars like the Lexus HS 250h, Mercedes-Benz R-Class and the full Maybach lineup appear, while the Ford Escape Hybrid, Mazda CX-7 and Hyundai Veracruz are all having their gaps filled with more modern and more fuel-efficient alternatives. Obvious exceptions to the rule include models that still sell in decent numbers like the Jeep Liberty and the Chrysler Town & Country (which will eventually be replaced by a crossover-like vehicle).
Check out our gallery of discontinued cars above, then scroll down for more information.

2018 Dodge Challenger SRT Demon First Drive | Don’t fear the Demon

"If you're not hurt, we'll be really pissed. If you are hurt, we'll still be pissed, but not quite as pissed." These are the words from Jim Wilder, the vehicle development manager of the 2018 Dodge Challenger SRT Demon, that echo through our head as we slide behind the wheel of the car for the first time. He was warning us about driving beyond our abilities, and keeping the car out of the wall. With 840 horsepower and 770 pound-feet of torque on tap from its supercharged, 6.7-liter V8, the Demon does 0-60 miles per hour in 2.3 seconds, and 0-30 mph in a second flat. If something does go wrong, it'll happen quickly. Following that talk, we had our guts sloshed as a passenger in a blurry eighth-mile run, giving us a taste of the G forces (the Demon can pull 1.8 G in a straight line) we'd feel when we got in the driver's seat for our own pass down the drag strip. We're already sweating. It had rained - you could describe it as torrential - the day before. The grassy parking areas surrounding Lucas Oil Raceway were still flooded, but any water on the pavement had evaporated and hung in the air. Combined with the heat, we were sticky and uncomfortable. In Drag Mode, the Dodge Demon's air conditioning turns off. Any condensation that it could leave on the track would be a problem, plus we need to reduce parasitic power losses for a faster run. The system is still working, though, the refrigerant diverted to the chiller system cooling the air coming into the engine. There's still condensation, but the Demon collects it on a catch pad to keep it from ending up on the pavement. We're also required to roll the windows up when entering the drag strip. For one thing, it helps keep the smoke out of the cabin during the pre-staging burnout. So, yeah, it's hot as Hell in the Demon. We pull through the water box and run through the sequence – which involves holding the "OK" button on the steering wheel usually used to navigate menus, and applying a specific amount of brake pressure before getting on the throttle to initiate the burnout. This gets any crud off the rear tires and heats up the rubber. There are multiple ways to launch the Demon. We had an instructor sitting in the passenger seat as we pulled up to the beams that trigger the Christmas tree at Lucas Oil Raceway. He walks us through the most complicated of the three he had explained to us just minutes before when we were in the passenger seat.