2012 Dodge Charger on 2040-cars

Auto blog

2020 Dodge Challenger Drag Pak comes solely with supercharged power

The Dodge Challenger Drag Pak has returned for 2020, five years after the last one arrived, and two years after it began development. And while in many ways it looks like past Drag Paks, there are a number of tweaks that should make this the fastest and most capable factory drag car yet from Mopar. Unlike the last model, only a supercharged 354-cubic-inch (5.8-liter for the imperically challenged) V8 is available. Mopar says it's more powerful than its predecessor, though exact horsepower wasn't given. It did confirm that the previous car was capable of a stunning 1,200 horsepower. The engine is coupled solely to a three-speed automatic transmission with a manual shifter. 2020 Dodge Challenger Drag Pak View 17 Photos Supporting the massive engine are many chassis, suspension and driveline enhancements. The independent rear suspension and axles are gone in favor of a solid axle from Strange and a four-link suspension. The front remains stock except for double-adjustable Bilstein shocks. The engine is mounted to a subframe member that's beneficial both to weight distribution and center of gravity. The car gets high-performance brakes and custom Weld Racing wheels with "DRAGPAK" engraved on them. The interior features a welded-in roll cage certified for quarter-mile times as quick as 7.5 seconds. Helping keep the car planted without increasing drag too much are front and rear spoilers from the road-going Challenger, a new addition compared with the previous car. Every Drag Pak car also comes standard with a wheelie bar and parachute. Dodge will only build 50 of these cars, and they'll only be offered as race cars that aren't legal for the street. The cars will be eligible for competing in sportsman classes in NHRA and NMCA drag racing series. Pricing and availability hasn't been set yet, but will be revealed sometime next year.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Chrysler recalling 67k trucks with manual transmissions

Earlier this month, Chrysler announced the recall of some 280,000 pickup trucks over concerns that their axles could seize up. Now the automaker has announced an entirely separate recall of another 66,819 trucks over the springs that could break in the clutch ignition interlock switch. The recall affects Dodge Ram 1500, 2500 and 3500 pickups, as well as the Dodge Dakota and Mitsubishi Raider. The issue is relevant only to those trucks fitted with manual transmissions, from the 2006 and 2007 model years and manufactured between July 1, 2005, and July 31, 2006. Since a broken spring could, according to statements issued by the National Highway Traffic Safety Administration and FCA US LLC (previously known as the Chrysler Group) prevent the vehicle from starting, or cause it to move unintentionally once the ignition kicks over, the automaker will begin notifying owners of the affected vehicles just before Valentine's Day to bring their trucks into their local dealers to have the clutch ignition interlock switch replaced. FCA emphasizes, however, that the unintended movement would only occur "in rare cases" and only "if recommended starting procedures are not followed." Only one such case is known to have occurred, but it did regrettably result in a fatality. Statement: Clutch Ignition Interlock Switch December 29, 2014 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary global recall of an estimated 66,819 older-model pickup trucks equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. An investigation by FCA US engineers discovered switches in certain model-year 2006 and 2007 pickups may be equipped with spring wire that differs from wire used in previous switches. The alternate wire may break and, as a result, the vehicles may not start. In rare cases, a vehicle may – if recommended starting procedures are not followed – exhibit unintended movement when its ignition key is turned. The Company is aware of one fatality related to this campaign. It stemmed from the single known accident involving this population of vehicles. The recall covers certain Dodge Dakota, Dodge Ram 1500, 2500, 3500 and Mitsubishi Raider pickups. Switches with the alternate wire were not used in any vehicles produced before July of 2005, or after June of 2006. The Dakota and Raider are no longer in production.