2007 Dodge Ram 2500 Slt 4x4 Automatic 4-door,led Lighting,bedliner,toolbox on 2040-cars

Auto blog

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Takata adds millions to recall expansion in US [UPDATE]

UPDATE: Ford spokesperson Kelli Felker has advised Autoblog that of the 1,509,535 total vehicles worldwide that the company is recalling, 966,504 of them are new additions for this expanded safety campaign. Last week, the National Highway Traffic Safety Administration announced that the Takata airbag inflator recalls would expand to an estimated 33.8 million vehicles in the US. However at the time, automakers weren't sure specifically which of their models might be affected under this enlarged campaign. Now, the numbers for BMW, FCA, Ford, and Mitsubishi are being released by the agency. Additionally, Honda is outlining the broadening of its own campaign. BMW's recall amounts to 420,661 vehicles in the US, an increase from 140,696 previously. All of the following models need their front, driver's side airbag replaced: 2002-2005 BMW 325i/325xi/330i/330xi Sedan 2002-2005 BMW 325xi/325i Sportswagon 2002-2006 BMW 330Ci/325Ci/M3 Convertible 2002-2006 BMW 325i/330i/M3 Coupe 2002-2003 BMW M5/540i/525i/530i Sedan 2002-2003 BMW 540i/525i Sportswagon 2003-2004 BMW X5 3.0i/4.4i BMW has received no reports of any injures or deaths from this problem in its vehicles. FCA has 5,224,845 vehicles globally in need of inflator replacements, according to its statement. However, the company is only aware of one injury related to the issue, which occurred in a 2006 Dodge Charger in southern Florida. There are 4,747,202 vehicles worldwide from the company that are affected on the front, driver's side. Among these, 4,066,732 are in the US, 374,508 are in Canada, and the rest are in other countries. The models are: 2005-2009 Dodge Ram 2500 Pickup 2004-2008 Dodge Ram 1500 Pickup 2006-2009 Dodge Ram 3500 Pickup 2007-2009 Dodge Ram 3500 Cab Chassis 2008-2010 Dodge Ram 4500/5500 Cab Chassis 2008-2009 Sterling 4500/5500 Cab Chassis 2004-2008 Dodge Durango 2007-2008 Chrysler Aspen 2005-2010 Chrysler 300/300C/SRT8 2005-2010 Dodge Charger/Magnum 2005-2011 Dodge Dakota 2006-2010 Mitsubishi Raider Also, there are 438,156 vehicles in the US, according to the NHTSA documents, that need their front passenger's side inflators replaced in the expansion of an earlier regional recall: 2003 Dodge Ram 1500 2003 Dodge Ram 2500 2003 Dodge Ram 3500 The total number of vehicles from Ford now covered under these campaigns stands at 1,509,535 worldwide. Of this total, there are 1,380,604 in the United States, 93,207 in Canada and 16,953 in Mexico.