2009 Dodge Grand Caravan Cargo 3.3l V6 1owner Full Service History Clean Carfax on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Dodge to reveal Hellcat-powered Challenger in Detroit?

On top of all the other performance car debuts slated for next week's Detroit Auto Show, we might be able to add one more to the list - the new, supercharged Hellcat V8 from Chrysler. According to new reports, the rumored 640-horsepower mill is likely to cross the Motor City stage in the engine bay of a Dodge Challenger.
As AllPar points out, though, there may be more news than just the fire-breathing engine. While we've seen spy photos of the Hellcat testing under the hood of the current Challenger, there's a very fair chance that it won't arrive until the muscle car is refreshed later this year. The question now is whether that refresh will be shown off alongside the new engine in Detroit, or if it'll be saved, perhaps for the New York Auto Show.
Other details dug up by AllPar include potential transmissions for the supercharged engine - the Mopar-minded site is expecting an eight-speed automatic or a Tremec six-speed manual. Prices, meanwhile, could be in the same elevated range as the Chevrolet Camaro Z/28, at $70,000 to $80,000.

Dodge Viper now available in matte finish

The prospect of buying a new Dodge Viper just got that much more enticing with the introduction of matte-finish paint direct from the factory. Available as part of the "1 of 1" customization program, the matte finishes aren't being offered in just a handful of colors like some other automakers do: customers will be able to specify a matte finish on any of the 8,000 colors that are already part of the program's palette. The matte finish option adds yet another step to the exhaustive hand-painting process that Dodge offers on the Viper - a painstaking endeavor that takes upwards of 145 man hours to complete. Specialists start by applying a base coat and a clear finish, followed by the paint and clear coat. The finished body panels are then smoothed with 1,000-grit paper and polished. A second sanding process is required for the matte finish before the application of a matte clear coat. Specify custom stripes (available in five colors or by custom order) and they're applied under the paint, not as decals on top. The availability of the matte finish in conjunction with the stripe options and new satin badging and fuel cap leads to over 50 million combinations. Needless to say, that means no two Vipers need ever leave the Conner Avenue assembly plant the same – though there will surely always be certain favorite combinations, especially on those units ordered from outside the customization program. Related Video: DODGE EXPANDS INDUSTRY-FIRST '1 OF 1' VIPER CUSTOMIZATION PROGRAM WITH NEW MATTE-FINISH PAINT OPTION - New matte-finish exterior paint available on all of Viper '1 of 1' program's 8,000 exterior color options and 24,000 stripe options - Viper's custom '1 of 1' exterior paint options double to 16,000 exterior colors and 48,000 unique strip combinations - Matte finish available in all exclusive '1 of 1' program and standard production colors - In addition to matte-finish exterior paint, Viper customers can choose between satin chrome or satin black badging and fuel filler door for a sinister appearance - Dodge Viper owners can build their one-of-a-kind Viper from more than 50 million unique build configurations for the ultimate in model year exclusivity June 19, 2015 , Auburn Hills, Mich. - The Dodge brand continues to expand the Viper's exclusive production elements like never before.