2014 Chevrolet Silverado 1500 Lt Crew Cab Pickup 4-door Save $10,000!! Brand New on 2040-cars

Auto blog

2019 Los Angeles Auto Show | Autoblog Podcast #605

In this week's Autoblog Podcast, Editor-in-Chief Greg Migliore is joined by Senior Editor, Green, John Beltz Snyder and Associate Editor Zac Palmer. This week, the main topic of discussion is the 2019 Los Angeles Auto Show. Of course, they've gotta talk about the Ford Mustang Mach-E — and its questionable naming scheme. They also run down some other L.A. show highlights including the Toyota RAV4 Prime, Kia Seltos, Lexus LC 500 Convertible and Audi RS Q8. Then they talk about the cars they've been driving: the 2020 Chevy Silverado with the Duramax diesel engine and the 2020 Subaru Legacy Touring XT. Autoblog Podcast #605 Get The Podcast iTunes – Subscribe to the Autoblog Podcast in iTunes RSS – Add the Autoblog Podcast feed to your RSS aggregator MP3 – Download the MP3 directly Rundown L.A. Auto Show 2021 Ford Mustang Mach-E (and here's a little more about the name) 2021 Toyota RAV4 Prime 2021 Kia Seltos 2021 Lexus LC 500 Convertible 2020 Audi RS Q8 2020 Chevy Silverado Duramax 2020 Subaru Legacy Feedback Email – Podcast@Autoblog.com Review the show on iTunes Related Video:

Bob Lutz builds the case for a mid-engined Corvette

Rumors of a mid-engine Corvette are like automotive industry folklore at this point. Every once in a while, news pops up that it might be happening or is under development, but nothing actually ever comes to fruition as something people can actually buy. The latest spy shots strongly suggest a mid-engine 'Vette is in the cards, yet again, possibly for 2018. Now, an op ed by former General Motors executive (and definite performance car fan) Bob Lutz in Road & Track gives the inside scoop on the history of one of these proposals and lays out how to make it happen today. According to Lutz, the company's engineers believed the C6 ZR1 was at the limit for front-engine, rear-wheel drive performance in that package, and the only solution was to move the powerplant behind the driver. Lutz even got then CEO Rick Wagoner on board. The scheme made it at least as far as clay models for mid-engine versions of the 'Vette and Cadillac XLR. Eventually, a lack of money got in the way, though, bringing the project to an end. Lutz puts a lot of faith in GM's current leaders, especially Mary Barra and Mark Reuss. He thinks the chances of a mid-engine 'Vette happening this time are better than 50 percent. The model, rumored to be named Zora, could offer over 700 horsepower in an ultra lightweight body and be priced at about $120,000 to "suck the doors off everybody." Head over to Road & Track to get some insights from this highly respected and entertaining auto industry veteran. Related Video:

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck