Fabulous 66 Chevrolet Impala on 2040-cars

Auto blog

Is the skill of rev matching being lost to computers?

If the ability to drive a vehicle equipped with a manual gearbox is becoming a lost art, then the skill of being able to match revs on downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. The usefulness of rev matching in street driving is limited most of the time – aside from sounding cool and impressing your friends. But out on a race track or the occasional fast, windy road, its benefits are abundantly clear. While in motion, the engine speed and wheel speed of a vehicle with a manual transmission are kept in sync when the clutch is engaged (i.e. when the clutch pedal is not being pressed down). However, when changing gear, that mechanical link is severed briefly, and the synchronization between the motor and wheels is broken. When upshifting during acceleration, this isn't much of an issue, as there's typically not a huge disparity between engine speed and wheel speed as a car accelerates. Rev-matching downshifts is the stuff they would teach at the automotive equivalent of the Shaolin Temple. But when slowing down and downshifting – as you might do when approaching a corner at a high rate of speed – that gap of time caused by the disengagement of the clutch from the engine causes the revs to drop. Without bringing up the revs somehow to help the engine speed match the wheel speed in the gear you're about to use, you'll typically get a sudden jolt when re-engaging the clutch as physics brings everything back into sync. That jolt can be a big problem when you're moving along swiftly, causing instability or even a loss of traction, particularly in rear-wheel-drive cars. So the point of rev matching is to blip the throttle simultaneously as you downshift gears in order to bring the engine speed to a closer match with the wheel speed before you re-engage the clutch in that lower gear, in turn providing a much smoother downshift. When braking is thrown in, you get heel-toe downshifting, which involves some dexterity to use all three pedals at the same time with just two feet – clutch in, slow the car while revving, clutch out. However, even if you're aware of heel-toe technique and the basic elements of how to perform a rev match, perfecting it to the point of making it useful can be difficult.

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.