Chevrolet Corvette on 2040-cars

Auto blog

Chevy admits there's confusion over Bolt and Volt names

Offering the possibility of 200 miles of driving range and the potential for a price of about $30,000, the Chevrolet Bolt is an incredibly enticing vehicle, and it has an opportunity to be a big player in the EV world. However, the hatchback has been plagued by one problem since the moment it debuted – the name. Bolt sounds very similar to Volt, Chevy's extended-range plug-in, and they can be easy to confuse in a conversation. That's not the best quality to have when trying to get a new vehicle's name out there among customers, and General Motors North America president Alan Batey told the Detroit Free Press that the company is aware of the problem. While the EV is definitely going into production, the model might be wearing a different moniker when it hits showrooms. "We're still in the decision phase. It could go either way," Batey said to the Free Press. He indicated the automaker still has about a year before a final decision is necessary. The Bolt will be built at GM's Orion Assembly plant in Michigan and will likely go on sale around 2017. That will put the Chevy on the market at roughly the same time as the 200-mile Tesla Model 3. Batey didn't seem too concerned, though. "Unlike Tesla, we can spread the cost over a whole lineup," he said to the Free Press. The future doesn't look quite so bright for the Spark EV, though. Batey suggested that it might not last once the longer-range Bolt fills that niche in the lineup. Related Video:

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Leveling kit now available for Chevy Colorado, but not yet for GMC Canyon

In various bits of news this year concerning the Chevrolet Colorado and GMC Canyon pickups, we kept hearing about a front leveling kit. GM Authority found a few details in early order guides in January. In February, the kit came up in relation to the Canyon's AT4 Off-Road Performance Package, and again with AEV's upgraded Colorado Bison. After three months of waiting, GMA has more info. The kit eliminates the trucks' raked stance by raising the front by one inch, using an electro-coated upper spacer and a polyurethane lower spacer in order to maintain the proper suspension geometry. Installation is a bolt-on job with low-profile nuts, but the task will require a spring compressor. Fitted properly, the kit doesn't void GM's new vehicle warranty on the Colorado. Why do we only mention the Colorado? Because for some reason, the kit isn't available for the Canyon yet as a standalone component; the GMC stays raked without one of the aforementioned option packages. For Chevy, the leveling kit is compatible with any trim in four-wheel drive except the ZR2. It cannot be installed on two-wheel-drive trucks, nor any truck wearing wheels that are 20 inches or above. The kit is available now, ordered through any Chevy dealer for $150. There is a treat in store for GMC buyers, though, but it requires spending a lot more money. GM Authority discovered that the 2021 Yukon will offer the brand's first illuminated emblem. Priced at $475 as a dealer-installed option, a backlit glow will show off the GMC logo in the grille. The brand makes the logo in red and black, it's thought the red logo will get the nod, at least at first. Only the front logo earns the spotlight, not the one on the tailgate. GMA says the tchotchke will be available on all four trims when the new full-size crossover goes on sale in a few months.