2004 Silverado 2500 Duramax Diesel on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Chevy Colorado and GMC Canyon get trim levels reworked again

GM Authority reports that GM has fiddled with trim packages on the Chevrolet Colorado and GMC Canyon for the 2021 model year, eliminating the base trims on both pickups and implementing small price changes. When the new model year goes on sale, the Chevy will lose the rear-wheel drive Base Extended Cab with the automatic transmission that starts at $22,395 after a $1,095 destination charge. The new entry-level is going to be the Work Truck model with the extended cab in rear-wheel drive, starting at $26,595 assuming the destination charge holds steady. That represents a $4,200 jump over the base 2020 model. MSRPs for the entire Work Truck lineup, from base to the Crew Cab Long Box, rise by $400. Elsewhere in the Colorado line, the four Z71 trims go down by $100, while the two ZR2 trims increase by the same amount. Only the six LT trims don't see any change.  The GMC side is a bit more involved due to previously announced changes. The 2020 Canyon comes in SL, Base Canyon, SLE, SLT, All Terrain, and Denali steps. Last month, GM Authority reported the 2021 Canyon would give all that up for the new names Elevation Standard, Elevation, AT4, and Denali. Since the SL base model retires in 2021, the Elevation Standard takes over at the entry level. Unlike on the Colorado, which sheds one trim, the Canyon lineup gets pared from 20 total combinations of trims, cab sizes, and bed lengths, to 14 total combinations. But like the Colorado, due to the loss of the cheapest configuration, the least expensive 2021 Canyon becomes $4,200 more expensive than in 2020, assuming the destination price remains the same. What's more, the 2021 Elevation Standard pricing adds $700 or $800 to the prices of the 2020 Canyon base and SLE models. There are more increases up the range. The 2021 Elevation trim replaces a combination of SLE and SLT models, bumping prices up by up to $900. In 2020, the least expensive All Terrain model is the Extended Cab Cloth for $37,695. For next year, the least expensive AT4 trim is the Crew Cab Short Box for $39,295. Like-for-like, though, the AT4 represents a $300 premium over the 2020 All Terrain Crew Cab Short Box. Three Denali trims will still stand at the top of the heap, each one going up by $400 in 2021. Until GM details the equipment changes, we won't know how the new pricing equates to value.

GM to squeeze out more production capacity for midsize trucks

General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video: