Beautiful 1972 Chevrolet C-10 Short Box 4x4 Pickup on 2040-cars

Auto blog

New Chevrolet Silverado to be revealed on Facebook on Thursday

There's not much to see here, but if you're one of those waiting for the reveal of the 2014 Chevrolet Silverado 1500, above is the teaser image that Chevrolet posted on its Facebook page. We've seen the truck in form-fitting camo before, and even less can be made out here beyond those seriously punchy Silverado-esque fenders and the knowledge that the projector-beam headlamps teased previously do indeed work. We'll have to wait until Thursday for a full perusal of the "bold exterior design" and "careful attention given to every detail" we've been promised.
Gathering intel and rumors, magnesium and aluminum contribute to the Silverado's weight loss plan, the purported "High Country" top-tier trim will contribute to luxury pickup truck competition and profit margins and the next-generation small-block V8 will contribute to improved fuel economy. On the engine note, there have been rumors of available V6 engines, and when Facebook user John Jones asked "Where's your answer to that EcoBoost Chevy?", the Bowtie replied "stay tuned on the 13th. We think you'll be pleased...".
Along with the "Raise the Bar" tag, Chevrolet says of the Silverado, "You asked, we delivered." You can watch the reveal live on Chevrolet's Facebook page at 9:30 am EST, this Thursday, December 13. The GMC Sierra 1500 will also be there, and we'll see both in person at the Detroit Auto Show in January.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM Ultium tech can scavenge heat from everywhere, even you

GM likes to give us tidbits about its Ultium platform from time to time, and today it’s telling us about the platformÂ’s ability to capture waste heat from the propulsion system. In addition to capturing from the propulsion system, it can also capture humidity from both inside and outside the vehicle and even from passengersÂ’ body heat. Yes, you, your family and/or your friends are a usable heat source as far as GM EVs are concerned. It then deploys the heat in an advantageous way. If at this point, youÂ’re screaming, "Heat pump!" youÂ’d be right. WeÂ’re talking about an elaborate heat pump system that GM is using for its Ultium-based vehicles. Every Ultium-based GM vehicle gets this system that is covered by 11 patents and four publications. The waste heat it collects is used in a number of ways, but its primary use is to heat the cabin quickly and efficiently. GM claims it can heat the cabin of its Ultium-based vehicles quicker than vehicles with traditional internal combustion engines. Plus, when put to use, GM claims that using the heat pump provides its EVs with up to 10% more range than theyÂ’d have without. Beyond heating the cabin, the heat pump is capable of putting waste heat to use by preheating the battery prior to charging so that you can charge quicker. The system can even cool the propulsion system in preparation for Watts to Freedom (WTF) launch control starts. GM says this was vital in helping the Hummer EV achieve its bonkers 0-60 mph time of about 3 seconds. “Having a ground-up EV architecture gives us the freedom to build in standard features like UltiumÂ’s energy recovery capabilities,” said Doug Parks, GM executive VP of global product development, purchasing and supply chain. “This helps us squeeze more efficiency, performance and overall customer benefit out of our EVs.” GM says itÂ’s been developing heat pump technology since the EV1 and its heat pump. This is the modern evolution of that technology, and GM says itÂ’s going to be implemented in every Ultium-based vehicle as a standard feature. Related video: Green Cadillac Chevrolet GM GMC Technology Electric Future Vehicles