1957 Chevy Belair on 2040-cars

Auto blog

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

Jaguar I-Pace vs. Tesla Model 3 and other EVs: How they compare on paper

The 200-mile club of electric vehicles is really growing. The most recent member is the Jaguar I-Pace, the company's first pure EV. It promises luxury, performance, style, and most important, good range. Nearly as recent is the Hyundai Kona EV, and while it doesn't promise luxury or performance like the Jaguar (it's also smaller), it does pack impressive range. With the introduction of both of these electric cars, we thought we would see how they compare against each other, and the other two big names in high-capacity electric cars: the Chevy Bolt EV and the Tesla Model 3. This isn't intended to be a direct, apples-to-apples comparison, as the four are quite different. If anything, they break into two groups: bigger and more luxurious, and smaller and less expensive. Then again, the number of vehicles with this electric range is small and comparisons to EV's with less range wouldn't be too kind to the other guys. If you want to learn more about these EVs, and compare them with other cars, be sure to check out our Car Finder and comparison tools. Horsepower and torque There is one clear winner here, and that's the Jaguar I-Pace. It packs a whopping 394 horsepower and 512 pound-feet of torque. That comes through a pair of electric motors (one at the front, another at the rear) that provide the Jag with all-wheel drive, the only one of these vehicles to offer it (at the moment). Altogether, it allows the I-Pace to have the best 0-60 mph time of 4.5 seconds. At the other end of the spectrum is the Hyundai Kona EV. It's front-drive, like the Bolt EV, and has effectively the same amount of horsepower as the Chevy at 201 horsepower, but its 0-60-mph time is almost a second slower. And the low-range version of the Kona, excluded because it doesn't go more than 200 miles between charges, is slower still. The Tesla Model 3 is the only vehicle with rear-wheel drive, and with a 0-60 mph of 5.1 seconds for the Long Range model, it is still very quick. Range and energy use Frequently, the all-consuming question with electric cars is, "How far can I go on a charge?" And to go the farthest, you need the long-range Tesla Model 3. It can go 310 miles. It has the added advantage of being able to use the network of Tesla Supercharger stations, though they are pay-per-use with the Model 3. Even the lower capacity Model 3, with just 220 miles of range, can use these stations.

Weekly Recap: GM plans massive new paint shop at Chevy Corvette factory

General Motors is laying out some serious green to maintain the Chevy Corvette's expansive color palette. The automaker is breaking ground on a new paint shop this summer that's part of a $439-million investment to upgrade the 34-year-old Bowling Green, KY, factory that builds the Stingray. The massive new structure will total 450,000 square feet, nearly half the size of the current 1-million square-foot facility. Construction is expected to take two years and won't impact Corvette production. The upgrades include new robots that save paint and create a better finish, longer, more efficient ovens to bake in the finish, and LED lighting. There's also a dry scrubbing booth technology with a limestone handling system that eliminates waste. GM has invested $135 million in the factory in last four years for the changeover to build the C7 and to relocate its Performance Build Center to Bowling Green. The improvements continue to modernize the Kentucky factory, which has become a tourist attraction in its own right, as more than 56,000 enthusiasts visited it last year. The upgrades are part of a $5.4-billion investment GM confirmed in April that will remake its US footprint in the next three years. The Bowling Green expansion underscores GM's continued commitment to the Corvette, which sold nearly 38,000 copies around the world last year, an eight-year high. "With this major technology investment, we can continue to exceed the expectations of sports car buyers for years to come," North American manufacturing manager Arvin Jones said in a statement. OTHER NEWS & NOTES Takata recall hits 34 million vehicles The National Highway Traffic Safety Administration expanded the Takata airbag recall to an almost unthinkable 34 million vehicles on Tuesday. The recall is part of an agreement reached by the two sides where Takata admitted some of its airbag inflators have a defect, and the deal compels the company to comply with all future regulatory actions and investigations. Takata's airbag inflators were produced with "a propellant that can degrade over time" and lead to ruptures, NHTSA said. Six deaths have been attributed to the flaw worldwide. Investigations conducted by Takata, automakers, and others have not determined the exact cause of the inflator problem, but NHTSA said moisture appears to alter the propellant's chemical structure. It then ignites too rapidly, creates too much pressure that ruptures the inflator, and blasts shards of metal at passengers.