1959 Chevrolet Other Pickups on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Would you pay $17 a month to give your older Ford connectivity?

When it was first introduced in 2007, there was nothing like the original Ford Sync system, since it allowed car owners to connect and use a portable device better than anything that came before it. And because it was a brought-in/tethered and software-based system, Sync leveraged a device's connectivity and was easily updated. It took competitors awhile to catch up: Toyota Entune wasn't available until 2011, and Chevy MyLink didn't roll out until 2012. But now Ford is the one playing catchup since it stuck with the brought-in strategy while most other automakers were quicker to add connectivity via an embedded cellular modem. Ford initially installed 2G/3G modems in its small fleet of electric and plug-in electric vehicles starting in 2012 so that owners could keep tabs on charging. Embedded connectivity came to Lincoln in 2014, and Ford began adding onboard 4G LTE via Sync Connect to select cars starting with the Escape in 2015. To get more cars connected more quickly, last week the automaker rolled out its FordPass SmartLink solution that plugs into the OBD port of 2010 to 2017 model year vehicles. This lets owners retroactively get onboard Wi-Fi, set up a "geo-fence" to keep tabs on a car's location, receive vehicle health reports and allows remote engine starting and door locking/unlocking using a smartphone app, among other features. But to connect older Ford vehicles will cost owners $16.99 a month for two years, not including installation. Ford throws in 1 GB of data or a 30-day trial, whichever comes first, after which owners have to add the vehicle to their Verizon shared data plan, which supplies connectivity for SmartLink, or establish a new account. (Disclosure: Autoblog is owned by Verizon.) By comparison, GM's 4G LTE data plans start at $10 a month for 200 MB and goes up to $30 for 3 GB, and owners can also add a car to an AT&T shared-data plan. But OnStar doesn't have a separate monthly subscription for the embedded modem or an installation charge, and standard features via the RemoteLink Mobile App are free for the first five years of ownership. FCA's Uconnect Access service also uses an embedded modem to provide similar telematics features for $20 per month following a free one-year trial, while a la carte in-car Wi-Fi is offered for $10 per day, $20 per week or $35 per month.

Diesel Power finds the ultimate modified oil-burner

For nine years, Diesel Power magazine has run the Diesel Power Challenge, this year's grindfest being "a week-long torture test that features seven events, nine trucks, 8,000 horsepower, and nearly 15,000 pound-feet of torque." The road to being crowned "the most powerful truck" starts with a dyno run, and then continues through the completion of a CDL-style obstacle course, an eighth-of-a-mile drag race while towing a 10,000-pound trailer, a quarter-mile drag race without a trailer, a fuel economy test in the mountains and finally a sled-pulling test through a 300-foot-long packed-mud pit.
What kind of trucks get into such a fight? Last year's winner, for instance - who upgraded his truck this year to prove he didn't "luck into the win" - drives a 2008 Ford F-250 Super Duty with a 6.4-liter Power Stroke V8 upgraded with a custom intake, Elite Diesel triple turbos and a two-stage nitrous system. Another competitor has a 2005 Dodge Ram 2500 powered by a 5.9-liter Cummins inline-six, upgraded with Garrett turbos, dual-stage nitrous, a seven-inch exhaust stack and twin fans built into the bed to cool the Sun Coast Omega transmission. The numbers on that truck: 1,255 horsepower, and 2,063 pound-feet of torque at the wheels. Naturally, as the image above might suggest, things don't always end well.
You'll find all five videos covering this years challenge below. A scene in the dyno video sums it all up perfectly: a competitor leaves his nitrous on too long and the crew is treated to some ominous poppings, he leans out the window, throws both hands up and shouts, "Amer'ca!"