No Reserve 1985 Chevrolet 3500 Dualie Dump Truck, Rebuilt 350 Engine, 4 Wheel D on 2040-cars

Auto blog

GM recalls select Tahoes, Yukons, Escalades for rear driveshaft issue

GM is recalling a number of its full-size SUVs due to an issue with the rear driveshaft assembly that could ultimately result in driveshaft failure. The actual number of total vehicles involved in the recall is small at just 1,789, but it’s spread out across the entire 2021 model year full-size GM vehicle lineup. That means a small number of every model is being recalled, including the Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL and the Cadillac Escalade and Escalade ESV. GM traced the issue back to certain driveshaft assemblies with ball bearings that were not properly heat treated. If theyÂ’re not properly heat treated, GM says that the balls may deform over time, causing noise and vibration. Continue to drive in this condition, and GM says the affected joint in the driveshaft assembly could seize, causing loss of drive power. However, the problem wonÂ’t present itself all at once, as GM says there will be a gradual increase of noises and vibrations before total failure. For those few owners with affected vehicles, GM says that it will replace the left and right rear driveshaft assemblies with properly-built units. Per usual with recalls, this will be done at your local dealership at no cost to the owner. If you have one of the recalled SUVs, expect to be notified mid-March. Related video:

Chevy Colorado and GMC Canyon get trim levels reworked again

GM Authority reports that GM has fiddled with trim packages on the Chevrolet Colorado and GMC Canyon for the 2021 model year, eliminating the base trims on both pickups and implementing small price changes. When the new model year goes on sale, the Chevy will lose the rear-wheel drive Base Extended Cab with the automatic transmission that starts at $22,395 after a $1,095 destination charge. The new entry-level is going to be the Work Truck model with the extended cab in rear-wheel drive, starting at $26,595 assuming the destination charge holds steady. That represents a $4,200 jump over the base 2020 model. MSRPs for the entire Work Truck lineup, from base to the Crew Cab Long Box, rise by $400. Elsewhere in the Colorado line, the four Z71 trims go down by $100, while the two ZR2 trims increase by the same amount. Only the six LT trims don't see any change.  The GMC side is a bit more involved due to previously announced changes. The 2020 Canyon comes in SL, Base Canyon, SLE, SLT, All Terrain, and Denali steps. Last month, GM Authority reported the 2021 Canyon would give all that up for the new names Elevation Standard, Elevation, AT4, and Denali. Since the SL base model retires in 2021, the Elevation Standard takes over at the entry level. Unlike on the Colorado, which sheds one trim, the Canyon lineup gets pared from 20 total combinations of trims, cab sizes, and bed lengths, to 14 total combinations. But like the Colorado, due to the loss of the cheapest configuration, the least expensive 2021 Canyon becomes $4,200 more expensive than in 2020, assuming the destination price remains the same. What's more, the 2021 Elevation Standard pricing adds $700 or $800 to the prices of the 2020 Canyon base and SLE models. There are more increases up the range. The 2021 Elevation trim replaces a combination of SLE and SLT models, bumping prices up by up to $900. In 2020, the least expensive All Terrain model is the Extended Cab Cloth for $37,695. For next year, the least expensive AT4 trim is the Crew Cab Short Box for $39,295. Like-for-like, though, the AT4 represents a $300 premium over the 2020 All Terrain Crew Cab Short Box. Three Denali trims will still stand at the top of the heap, each one going up by $400 in 2021. Until GM details the equipment changes, we won't know how the new pricing equates to value.

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.