1963 Chevy C-10 on 2040-cars

Auto blog

2014 Chevrolet Malibu gets more torque, more room and inspiration from the Impala

The 2014 Chevrolet Malibu, having stared at the Impala across the showroom floor for a year, gets nips and tucks all over inspired by its larger brother. The 2.5-liter four-cylinder in the base car will get a stop-start system and 23 city miles per gallon, 35 highway, each number representing a one-mpg improvement over the 2013 car. Output is 196 horsepower and 186 pound-feet of torque.
Opt for the 2.0-liter turbo and, while power holds steady at 259 hp, torque goes up by 14 percent to a striking 295 lb-ft (a figure Chevy calls best in the class). The final details include newly programmed transmission shift points and faster shifts, for better engaging and enjoying the added power.
Looks-wise, the grille's been reshaped to be more in line with the new Chevrolet look, a narrower upper grille hovering over a larger lower grille.

GM invests $175 million in Chevy Camaro factory

General Motors just keeps rolling out portions of its $5.4-billion plan for factory upgrades over the next three years. In the latest announcement, the automotive giant is putting $175 million into the Lansing Grand River Assembly Plant for improvements to build the 2016 Chevrolet Camaro. The investment brings new equipment to the plant to build the pony car. An upgrade is needed to support Camaro-specific colors like Summit White, Bright Yellow, and Red Hot, and the factory is also getting two robotic framers. A second shift of 500 workers is resuming in Lansing later this summer to produce the model, as well. So far, GM has announced allocations for $2.8 billion of the $5.4 billion in upgrades. The investments include $1.2 billion to improve pickup production, $439 million for a paint shop for the Corvette, and more new equipment at other plants too. Lansing Grand River Plant Tools Up for 2016 Camaro $175 million investment enables production of lighter, more powerful model 2015-05-28 LANSING, Mich. – A $175 million investment for new tooling and equipment for the sixth-generation Chevrolet Camaro, and the return of hundreds of workers to build America's best-selling performance car for the last five years, was announced today. The facility improvements include three new paint systems for Camaro-specific colors: Summit White, Bright Yellow, and Red Hot. The investment also includes installation of two robotic framers, which allow better dimensional control to provide a more precise drive experience. The Lansing Grand River Assembly Plant will resume a second shift of 500 jobs in late summer. The all-new Chevrolet Camaro was introduced on Detroit's Belle Isle on May 16. The current generation Camaro has been America's favorite performance car for five consecutive years, attracting both long-term Camaro fans and new buyers to Chevrolet. To improve on that success, the sixth-generation Camaro elevates every aspect of Camaro with a suite of new technologies, even higher levels of performance and fuel economy, and a leaner, more athletic design. "I may be the luckiest mayor in America today," said Lansing Mayor Virg Bernero. "Gearing up for full-scale production of the legendary Chevy Camaro is a new high point in the more than two decades of extraordinary partnership between the City of Lansing, General Motors and the UAW.

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video: