2014 Cadillac Ats 2.5l on 2040-cars

Auto blog

Cadillac flagship, possible production Elimiraj, caught testing

One of the biggest debuts at the Monterey car week, both literally and figuratively, was the Cadillac Elmiraj Concept. The massive coupe made quite a splash with the show's well-heeled guests. Now, we have what might be the very first images of the Elmiraj, or whatever it may be called when it reaches production, out testing.
Don't let that modified Chevrolet Caprice body fool you, this car is about four to six inches longer than Chevy's US-spec cop car, from the A-pillar forward. According to our spy, with the Caprice at 203 inches and the concept at 205, adding a few extra inches here and there fits the bill for the four-door Elmiraj that was hinted at in Jay Leno's Garage.
There are a number of other classic mule signs on this car, including a cover over the fuel door and heavily modified front and rear fascias, each of which serves to hide some significant change from the standard Caprice. Using a Caprice for development also, hopefully, hints at something that big Cadillacs like the XTS have lacked - rear-wheel drive.

[UPDATE] Cadillac Blackwing gets ticket to Italy, to go to work in a supercar

UPDATE: It seems MAT's belief it had secured a supply of Cadillac's 4.2-liter Blackwing V8 was premature, and based on a handshake deal before GM sold its Turin engine center to Italy's Punch Group. Shortly after Hagerty ran the story, GM sent a statement to the outlet reading, in part, "We do not have an agreement in place with Manifattura Automobili Torino (MAT) to provide or sell the Blackwing engine. ... Our team is following up with MAT president Paolo Garella to discuss the misunderstanding." MAT also submitted a statement to Hagerty, saying, in part, "We thank GM for the clarification. Although a signed agreement was not finalized between the parties, we were under the impression that our counterpart was committing to making this engine available to MAT at conditions yet to be defined. ... We hope that this misunderstanding will not compromise our relations with GM and possible future collaborations." The original article follows: Some necessary cost-cutting at Cadillac led to switching the new CT4, CT5, and Escalade to older platforms. The revised architecture plan meant Cadillac's newest top-tier products couldn't fit Cadillac's newest top-tier engine, the 4.2-liter twin-turbo DOHC V8 known as Blackwing. That engine would serve limited duty at full power in the now-dead CT6-V, and at reduced output in the CT6 Platinum V8 trim before ending its bright, brief domestic life. But the story isn't over, the rebirth of Blackwing coming from a most surprising locale: Turin, Italy. Before the canceled Geneva Motor Show, Hagerty spoke to Paolo Garella, CEO of Manifattura Automobili Torino; that's the company better known as MAT, makers of the New Stratos and contract engineering house for boutique screamers like the Aspark Owl electric hypercar, Apollo Intensa Emozione, and SCG003C. Garella told the outlet, "We have an agreement with General Motors" for a supply of Blackwings, which would be developed and built at the General Motors Propulsion Engineering Center (PEC) in Turin. Since 2005, the PEC has been used to develop GM's global diesel engines and electronics. MAT's plan is to put the V8 into a new limited-run car MAT is creating from its own design. Then another surprising turn: Belgium-based global auto supplier Punch Group bought the PEC, with plans to work with GM on projects in progress until at least the end of 2021. Nothing changes as far as MAT is concerned, except perhaps a chance for an even closer collaboration with Punch Turin.

Even if GM does close all 5 of those plants, it'll still have too many

DETROIT — General Motors' monumental announcement on Monday that it will close three car assembly plants and two powertrain plants in North America and slash its workforce will only partially close the gap between capacity and demand for the automaker's sedans, according to a Reuters analysis of industry production and capacity data. Sales of traditional passenger cars in North America have been declining for the past six years and are still withering. After GM ends production next year at factories in Michigan, Ohio and Ontario, it will still have four U.S. passenger-car plants — all operating at less than 50 percent of rated capacity, according to figures supplied by LMC Automotive. In comparison, Detroit-based rivals Ford and Fiat Chrysler Automobiles will have one car plant each in North America after 2019. The Detroit Three are facing rapidly dwindling demand for traditional passenger cars from U.S. consumers, many of whom have shifted to crossovers and trucks. Passenger cars accounted for 48 percent of retail light-vehicle sales in the United States in 2014, according to market researchers at J.D. Power and Associates. This year, sedans will account for less than a third of light vehicle sales. That shift in turn has left most North American car plants operating far below their rated capacities, while many SUV and truck plants are running on overtime. The collapse in passenger-car demand is a challenge for nearly all automakers in the United States, including Japan's Toyota and Honda, which have the top-selling models in the compact and midsize car segments. Toyota executives said last month they are evaluating the company's U.S. model lineup. But Toyota also plans to build compact Corolla sedans at a new $1.6 billion factory it is building in Alabama with partner Mazda. The obstacles facing GM in its plans to close more auto factories became apparent on Tuesday as U.S. President Donald Trump threatened to block payment of government electric vehicle subsidies to GM. While it is not certain that Trump unilaterally has the power to do that, he made it clear he intends to use his office to pressure the company to keep open a small car plant in Ohio that GM says will stop building vehicles in March.