Le 2.4l on 2040-cars

Auto blog

How Toyota's 100-year textile history influenced FCV hydrogen fuel cell car

Turns out, Toyota had a surprising ace in the hole when it came to building the new fuel tanks for the FCV hydrogen fuel cell car, which is coming next year. Well before Toyota became the Toyota Motor Company, it was the Toyota Industries Corporation and it made textile looms. This is important because the main structure of the hydrogen tank is wound carbon fiber. When Toyota set out to increase the strength of the tanks to hold hydrogen stored at 10,000 psi (up from 5,000 in the previous tanks), it was able to draw on its 100-year-old history as it designed its car of the future. "A lot of that textile experience came back when we did the tank wrapping." – Justin Ward "We have a lot of experience with textiles," Justin Ward told AutoblogGreen at the 21st World Congress on Intelligent Transport Systems (ITS) in Detroit this week, "and a lot of that textile experience came back when we did the tank wrapping." On top of being able to hold the higher-pressure hydrogen, Toyota's first attempt to build its own hydrogen tank was six times faster than the industry standard, so it saved time and money as well as working better. The company will also be able to inspect its own tanks. Ward is the general manager of powertrain system control at the Toyota Technical Center and hydrogen vehicles are something he knows a lot about. The reason for the stronger, 10,000-psi tanks is because the 5,000-psi tanks only offered around 180-200 miles of range, even with four tanks in the early $129,000 FCHV Highlander hydrogen prototypes. The FCV only has two, but they will able to deliver the 300-mile range that customers told Toyota they wanted. Dropping the number of tanks not only obviously reduced the cost for the tanks themselves but also the number of valves and hoses and other components you need. Despite the benefits of higher compression, going much higher doesn't make sense. 10,000 psi is the "natural progression," Ward said, because "you start to bump up against compression inefficiencies." Think of an air compressor. When hydrogen is produced at a wastewater treatment plant or a reforming site, Ward said, is it at around ambient pressure (14 psi). That has to be raised, using compressors, all the way to 10,000 psi. "That takes energy," Ward said, "and every doubling of pressure adds another doubling of energy needed, so it starts to add up pretty fast if you go too high." Component specifications are also fine at 10,00 psi, but more difficult at higher levels.

PickupTrucks.com's latest test results in a familiar winner [w/video]

PickupTrucks.com has gone and thrown the latest batch of half-ton pickups into a cage match to see who would come out on top. The site put the 2014 Chevrolet Silverado 1500, GMC Sierra 1500, 2013 Ford F-150, Ram 1500, Toyota Tundra and Nissan Titan through a battery of tests. Those included 0-60 miles per hour acceleration, 60-0 mph deceleration, fuel economy, a hill climb, and payload and towing. They even threw the rigs on an autocross course to evaluate overall handling. Each truck was given points based on how it scored in each evaluation.
Who came out on top? Somewhat surprisingly, the 2013 Ford F-150 walked away with the gold, though fewer than 50 points separated first and fourth place. Head over to PickupTrucks.com to read the full evaluation and the final results. You may be shocked to see exactly where some of the segment's newest additions placed. You can also watch a video on the test below.

J.D. Power study sees new car dependability problems increase for first time since 1998

For the first time since 1998, J.D. Power and Associates says its data shows that the average number of problems per 100 cars has increased. The finding is the result of the firm's much-touted annual Vehicle Dependability Study, which charts incidents of problems in new vehicle purchases over three years from 41,000 respondents.
Looking at first-owner cars from the 2011 model year, the study found an average of 133 problems per 100 cars (PP100, for short), up 6 percent from 126 PP100 in last year's study, which covered 2010 model-year vehicles. Disturbingly, the bulk of the increase is being attributed to engine and transmission problems, with a 6 PP100 boost.
Interestingly, JDP notes that "the decline in quality is particularly acute for vehicles with four-cylinder engines, where problem levels increase by nearly 10 PP100." Its findings also noticed that large diesel engines also tended to be more problematic than most five- and six-cylinder engines.