2022 Ram 1500 Limited Crew Cab 4x4 5'7" Box on 2040-cars

Auto blog

Chrysler banks $507 million in Q2, trims 2013 earnings forecast

Chrysler has some good news and some bad news. First, profits were up 16 percent over the second quarter of 2012, bringing the Auburn Hills, Michigan-based manufacturer $507 million on the back of strong demand for trucks and SUVs (a recurring theme this quarter, particularly in the US). Q2 revenue was up as well, from $16.8 billion in 2012 to $18 billion in 2013. The bad news is that the Pentastar's overall earnings forecast for net income in 2013 has been trimmed from $2.2 billion to between $1.7 and $2.2 billion, according to Automotive News.
In addition to the adjusted net income forecast, Chrysler tweaked its operating profit from $3.8 billion to between $3.3 and $3.8 billion. This has gone largely unexplained by Chrysler, perhaps hoping the news of a three-percent increase in its transaction prices for Q2 will allow it to sweep this adjustment under the rug.
The star of the show for Chrysler has been its US sales, which saw a 10-percent jump, both bettering the industry average of eight percent and improving over the same stretch of 2012. As with the increase in transaction prices, Chrysler has the new Ram pickup and Jeep Grand Cherokee to thank. Perhaps most worrying from this report, though, is that every brand in the automaker's stable saw an increase in sales... except for the Chrysler brand itself.

Chrysler recalling 382k Ram HD diesel pickups, 184k SUVs

Between GM's ignition switches and Takata's airbags, it's been a big year for recalls, but they keep rolling in. The latest comes from Chrysler, which has announced a pair of recalls for certain heavy-duty pickups and SUVs.
The first issue revolves around the 6.7-liter Cummins diesel engine available in the 2010-2014 Ram HD trucks, including 2500 and 3500 series pickups as well as 4500 and 5500 series chassis cabs. In the affected units, "a terminal connector near the fuel heater may be subject to friction-induced corrosion," according to the first of the two announcements from Chrysler below.
The problem could result in overheating and fuel leakage. Chrysler launched its investigation following cases of overheating, none of which actually started a fire, much less an injury or accident. As a precautionary measure, however, Chrysler is instructing service technicians to replace the terminals on an estimated 381,876 Ram units around the world - the vast majority of those (314,704) registered in the US, another 59,432 in Canada, 1,803 in Mexico and 5,937 abroad.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.