2006 Mercury Mountaineer on 2040-cars

Auto blog

Ford recalls 382k vehicles across six campaigns

Ford needs to repair a total of 381,633 vehicles in North America across six newly announced campaigns, including five safety recalls and one compliance recall. By far the largest of these campaigns covers the 342,271 examples of the 1998-2003 Windstar to double check an earlier recall repair. Among these, 283,413 are in the US and 58,858 are in Canada. The combination of corrosion and stress can cause cracks in the rear axle and eventually lead to the part to snap completely. The company reports a small number of accidents might be connected to this, but there are no injuries. The minivans were recalled for this issue back in 2010, and it was investigated by NHTSA. According to Ford's latest announcement, the reinforcement brackets on some of these models might not have been installed correctly. This time, dealers will perform an inspection. Minivans with incorrectly installed brackets will get a new rear axle. The rest of the owners will be offered a deal to replace the part at a reduced cost. The next largest campaign covers 36,857 examples of the 2015 F-150 to fix a problem with the adaptive cruise control. Specifically, there are 33,481 affected trucks in the US, and 3,376 in Canada. According to Ford, "when passing a large, highly reflective truck" the radar in the system can misidentify a semi as being in the same lane as the pickup. The collision warning system would then activate, slowing the F-150. There's one report of an accident with this happening but no injuries. The fix is simply an update to the adaptive cruise control module software. Ford also has a recall for 1,477 examples of its 2016 F-53 and F-59 stripped chassis models, and they're all located in the US. A manufacturing issue might allow the trucks to shift into reverse without the driver first applying the brakes. There are no reports of any accidents from this, though. To repair the problem, the models get a new transmission shift control bracket and an adjustment to the shift cable. The Blue Oval's safety compliance recall covers 708 examples of the 2016 Fusion and Lincoln MKZ, including 658 of them in the US, 28 in Canada, and 22 in Mexico. On these models, a manufacturing problem with the fuel tank could allow it to crack in a crash, which isn't allowed under federal rules. There are no reports of accidents, injuries or fires. The fix will be a new fuel tank for all of them. The company is also repairing 251 units of the 2015 Taurus and Lincoln MKS, plus the 2016 Explorer.

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: