1984 Mercury Grandmarquis 47k Actual Miles on 2040-cars

Auto blog

Junkyard Gem: 1991 Mercury Capri

Ford has gotten a lot of use out of the Capri name in the United States. First, there was the Lincoln Capri in the 1950s, followed by the Ford Capri Mk1 (which was sold by Mercury dealers in the USA but never actually badged as a Mercury). Then came the 1979-1986 Mercury Capri, built on the very successful Fox Platform and essentially a clone of the Mustang. Finally, in 1991, the Australian Ford Capri came to the United States. Here is an example of this rare car that I spotted in a Northern California self-service yard not long ago. Mechanically speaking, the 1991-1994 Capri was a Mazda 323 under the skin, complete with a member of the same B-series engine family that went into such cars as the Miata and Ford Escort. So, for a few years in the early 1990s, car shoppers who wanted a sporty Mazda convertible could choose between a Miata and a Capri. The Capri had front-wheel-drive, but could be had with factory turbocharging. These cars were reliable and fun, but had a tough time competing with the Miata in the showroom battles. You'll see the occasional example now and then, but most of the 1991-1994 Capris have met the same fate that awaits this one. Related Video:

Ford Recalling 70k Escape and Mariner Hybrids for cooling issue

Ford is recalling about 70,209 examples of the 2005-2008 Ford Escape Hybrid and the 2006-2008 Mercury Mariner Hybrid because the cooling pumps for their hybrid systems could fail.
According to the company's defect notice, it's possible for the original "Motor Electronics Coolant (MEC) Pump" to wear out and fail, which would could cause the hybrid system to overheat. If this happens, the vehicle goes into a safety mode that takes away most or all of its power. However, braking and steering still operate normally. After cooling down, the affected models restart normally. The company says that it's not aware of any accidents or injuries related to this problem.
Ford will begin repairing the vehicles in late October, and dealers will be installing improved, brushless pumps on the affected models at no charge to owners. If drivers had their pumps fail before this recall, they can contact Ford for a possible reimbursement. Scroll down to read the recall announcement from the National Highway Traffic Safety Administration or download the full defect notice as a PDF, here.

Ford finds flex-fuel engine design plays big role in emissions output

How bad is ethanol for your engine? There's been a lot of debate on this issue as the US considers upping the biofuel content in the national gasoline supply from 10 percent (E10) to 15 percent (E15). The ethanol industry and some scientists say higher ethanol blends show no "meaningful differences" in new engines while the oil industry says ethanol creates health risks. Researchers working at the Ford Research and Innovation Center decided to take a closer look at how a wide range of gas-ethanol blends - E0, E10, E20, E30, E40, E55 and E80 - affected the emissions coming out of a flex-fuel 2006 Mercury Grand Marquis. To see the full report, printed in the journal Environmental Science & Technology, requires payment, but there is an abstract and Green Car Congress has some more details. The gist is that, "with increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased." At least NOx and NMHC emissions decreased. The researchers say that the effects are due to the fuel and "are expected for all FFVs," but that the way that a manufacturer calibrates the engine will affect NOx, THC, and NMOG emissions. It's this last bit that's important, since the researchers found, "Higher ethanol content in gasoline affects several fundamental fuel properties that can impact emissions. ... These changes can have positive or negative effects that can depend on engine design, hardware, and control strategy. In addition to direct emissions impacts, higher ethanol content fuel can also provide more efficient combustion and overall engine operation under part-load conditions and under knock-limited higher-load conditions." So, as we head towards more ethanol in our fuel supply (maybe), manufacturers are going to need to learn how to burn it most efficiently.