Gmc Savana Conversion Van on 2040-cars

Auto blog

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.

GM will no longer remove parts from trucks to calculate curb weights

Following last week's mild uproar after it was discovered that Ford and General Motors were removing some optional parts from their pickups to lower the curb weight and consequently increase the maximum payload, GM has come out and committed to a base curb weight for its upcoming Chevrolet Colorado and GMC Canyon compact trucks (although it has yet to publish them) and its current Silverado and Sierra. The company will do the same for its heavy duty offerings, although those numbers have not been finalized yet.
"This will make our curb weight and payload specs more consistent with those of most other truck makers, making it easier for customers to compare vehicles," GM spokesman Tom Wilkinson told Autoblog in an emailed statement.
As GM notes - and as every manufacturer has noted since this story broke - customers still shouldn't take max payload ratings as gospel. Instead, they should refer to their truck's Tire and Load Label, like the one shown at the inset, which will offer detailed information on max payload, specific to their truck.

GM planning to put its fullsize pickups on a big diet, too

General Motors is just coming off a complete redesign of the Chevrolet Silverado and GMC Sierra for 2014, but in the US fullsize truck market, there is no rest for the weary. According to Reuters, plans are already unfurling for both trucks to drop pounds from their curb weight over the next few years, but this will unlikely be able to keep pace with the 700-pound diet targeted for the next-generation Ford F-150, a truck expected to debut late next year.
The biggest weight reduction for these trucks might not be available until the next full redesign, which will likely happen around 2019, but the article says that smaller updates could shave pounds in the meantime. Two examples given include an "aluminum-intensive" version of the Silverado that could shed 250 pounds and debut around the same time as the lighter-weight, aluminum-bodied 2015 Ford, and there is also talk of reducing weight for driveline components such as axles and driveshafts. These changes are all part of an attempt to meet strict new fuel economy standards coming in 2017, targets which will get even tougher in 2025.