We Finance '08 Suv Awd Clean Carfax Entertainment Leather And More.... on 2040-cars

Auto blog

GMC could have used Jeep's prized grille design on its born-again Hummer

General Motors confirmed it's bringing the Hummer nameplate back on an electric, GMC-badged pickup by publishing a dark photo of its front end. The battery-powered drivetrain under the sheetmetal represents a tectonic shift, but we noticed another flagrant break with tradition: it wears six slot-like inserts instead of seven like on every previous Hummer and countless Jeeps. Adding an extra slot wouldn't have landed GMC in hot water. The seven-slot grille has historically been associated with Jeep, and the company proved it's willing to go to significant lengths to ensure another automaker — especially one it perceives as a rival — doesn't use it. Parent company Fiat-Chrysler Automobiles (FCA) bitterly sued Mahindra over the Roxor's design, including its five-slot grille, and won in 2019, forcing the Indian firm to unveil a redesigned side-by-side for the 2020 model year. And yet, stylists would have very likely been able to get away with it on the Hummer. While General Motors owns Hummer, the brand traces its ancestry to 1970, when American Motors Corporation (AMC) purchased Jeep from Kaiser and changed the name of its General Products Division to AM General Corp. The division manufactured the rear-wheel drive, CJ-based DJ for the United States Postal Service and began developing the Humvee in 1979. Jeep and AM General went their separate ways when Renault began investing in AMC. Foreign companies weren't allowed to own defense contractors, and AMC had more to gain by gradually selling out to Renault than by keeping AM General, so it divested the division to LTV Corporation in 1983. Humvee production started shortly after, but no one protested its seven-slot grille because there was no risk of it stealing sales from a comparable Jeep model. It was manufactured exclusively for the U.S. Army, and civilian sales weren't planned. H2SUV View 4 Photos The original civilian Hummer released in 1992 must have raised more than a few eyebrows but, here again, it didn't directly compete with one of Jeep's off-roaders, so no one complained. It was huge, correspondingly expensive, and its portal axles made the YJ-generation Wrangler wet its pants. It's the H2 concept (pictured above) unveiled at the 2000 Detroit Auto Show that set off alarm bells in Auburn Hills. DaimlerChrysler's lawyers counted the slots in the chrome-plated insert that dominated its front end and shuddered when they reached seven.

Specialty Vehicle Engineering's 750-horsepower GMC Canyon fully revealed

GMC's celebrated Syclone will turn 30 in early 2021, but nothing suggests the company will mark the occasion by releasing a modern interpretation of the pickup. New Jersey-based tuner Specialty Vehicle Engineering (SVE) is taking the matter into its own hands by building a limited number of GMC Canyon trucks with Hellcat-like power. Although the original Syclone received a turbocharged V6, the 2021 model gains a 5.3-liter V8 normally found in bigger vehicles, including the Sierra and Yukon. SVE rebuilt it with forged aluminum pistons, forged steel connecting rods, high-lift valve springs, a custom crankshaft and upgraded fuel injectors among other aftermarket parts. It also added a supercharger to raise the eight's output to 750 horsepower and 600 pound-feet of torque. Power flows to the four wheels via a strengthened 8-speed automatic transmission and a permanent all-wheel-drive system. For context, the first Syclone gave the Chevrolet Corvette a run for its money with a fuel-injected, 4.3-liter V6 turbocharged to 280 horsepower and 360 pound-feet of torque. These numbers were spectacular in the early 1990s since the Sonoma that Syclone was based on shipped with the 105-horse Iron Duke four-cylinder as standard. Even compared with the Sonoma GT that got a naturally aspirated 4.3-liter V6 with 195 horsepower and 260 pound-feet of torque, the Syclone was impressive. SVE installed six-pistons front calipers that clamp 13.6-inch slotted rotors, and it kept the factory brakes out back. It also lowered the suspension by two inches in the front and five inches in the back, upgraded the shocks, and added a heavy-duty rear sway bar. These modifications help drivers make the most of the extra power, but SVE hasn't published performance specifications (like the truck's zero-to-60-mph time) yet. Surprisingly, the eight-cylinder weighs almost the same as the V6 it replaces so the engine swap doesn't affect weight distribution. Visually, the Syclone can't be mistaken for a run-of-the-mill Canyon. It wears a deep front bumper, has cladding over the rocker panels and rides on 20-inch alloys. Edition-specific emblems round out the look, and the list of options includes a body-colored grille as well as a folding tonneau cover. SVE's images show a truck painted black, which was the only color offered on the 1991 model, but it's available in any factory hue. Inside, the modern-day Syclone gains special floor mats and a numbered plaque on the dashboard. Leather is optional.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck