2003 Ford Windstar Se Mini Passenger Van 4-door 3.8l on 2040-cars

Auto blog

Focus STs for SEMA include Lotus and Gulf liveries, rally-fied police car

Ford, as we mentioned on Saturday, is pulling out all the stops for November's SEMA show, bringing 57 vehicles to the Las Vegas event. Ford will be staggering the release of its SEMA flotilla, though, so expect to hear a lot about the new additions to the fleet in the weeks to come. We already showed you the Fiesta, Fiesta ST and Mustang models that made up the first batch of SEMA cars. Next up, we have a quartet of modded Focus STs joining Ford's SEMA roster.
Our first Focus ST (pictured above) sports the legendary livery of Gulf Racing. The orange-on-blue scheme, which Ford helped make famous at the 24 Hours of Le Mans, has been updated for 2013, with a more vibrant blue. This ST was built by Universal Technical Institute, while the exterior was done by Neil Tjin of Tjin Edition. Side exhausts, a Vortech supercharger and a Motiv Concepts high-flow cat allow the ST to breathe a bit easier, while Forgestar wheels contrast well with the iconic paint scheme.
Focus ST number two has been done-up by PM Lifestyle and is inspired by "Southern California car culture." Sporting a sleek, pale blue paint job, there's also no shortage of carbon fiber on the car's exterior. The 2.0-liter, turbocharged, four-cylinder engine has been massaged by the likes of Banks Power, COBB Tuning and Ford Racing, while the suspension is wearing a shiny, new set of coilovers and sway bars. The meaty brakes, tucked behind 19-inch, Rotiform wheels, come from Wilwood, while the cabin has been fitted with a pair of Sparco Chrono seats and five-point, Schroth harnesses.

70% of pickups could use aluminum by 2025

In the next decade, the auto industry will see an explosion in its use of aluminum to cut weight and increase fuel economy, according to a study from market analysts Ducker Worldwide cited by The Detroit News. We are already seeing the lightweight metal show up extensively in luxury models from Europe, but with the impending launch of aluminum-intensive 2015 Ford F-150 (pictured above), North America is using it even more, as well. The report predicts 70 percent of US pickups to have aluminum bodies by 2025.
It won't just be pickups that see the benefit, though. The average amount of aluminum in US vehicles is forecasted by the study to grow from an average of 350 pounds in 2013 to about 550 pounds by 2025. The most common parts to use it will be hoods, doors and - to some extent - roofs, as well.
The massive increase in pickups' aluminum content hardly seems surprising. The F-150 is predicted to use so much that it might cause a short-term shortage, according to one earlier report. At the same time General Motors is heavily rumored to be negotiating with suppliers for the next generation Chevrolet Silverado and GMC Sierra. Ram is the last holdout of the Big Three, but the study predicts that not to last.

Ford F-150 EcoBoost in NHTSA probe for acceleration issue

According to Automotive News, the National Highway Traffic Safety Administration is launching a probe into 400,000 Ford F-150 models over possible acceleration problems. According to the article, NHTSA has received 95 reports "alleging incidents of reduced engine power during hard accelerations" on 2011 to 2013 F-150 models equipped with the company's 3.5-liter EcoBoost V6 engine.
Automotive News reports that Ford has issued three technical service bulletins "related to intermittent stumble/misfire on acceleration from highway cruise in humid or damp conditions," according to the government agency's documents. About one third of the 95 reports NHTSA has received cited humid or rainy conditions when these problems allegedly occurred.
These technical service bulletins have allowed dealers to address a "condition related to moisture accumulation in the charge air cooler during extended highway cruising at constant throttle in humid or damp conditions," AN reports, citing NHTSA documents. Furthermore, the TSB outlines details for "reprogramming the powertrain control module with the latest calibration and installing a new CAC and air deflector plate."