2014 Ford Fiesta Se on 2040-cars

Auto blog

Shelby GT350R offers first mass-produced carbon fiber wheels

In the world of race engineering, reducing total weight is good, but reducing unsprung weight is flippin' fantastic. That's the reason Ford is pushing the envelope in terms of technology for the Shelby GT350R's wheels. Joining the likes of Koenigsegg in the offering, Ford has teamed with Australian outfit Carbon Revolution to produce the CF rollers en masse for the first time. Destined for the hubs of the new Shelby GT350R, the new hoops weigh just 18 pounds each, versus the 33-lbs weight of a similar aluminum wheel. On top of slashing up to 60 pounds in unsprung weight, there's such a reduction in rotational inertia – 40 percent, versus aluminum wheels – that Ford actually has to recalibrate the magnetic ride control system and springs. Thanks to, we're guessing, scenes of crashed Formula One cars disintegrating and spewing shards of carbon fiber all over the track, Ford seems quite keen to do away with the idea that CF is strong, but brittle. The company conducted extensive shock testing, ramming a wheel into a curb at speed. According to the Blue Oval, the lightweight wheel allowed the suspension to respond so quickly that the impact was "greatly diminished," causing the tester to run the experiment again, thinking there'd been a mistake. After recording brake rotor temperatures of 900 degrees Celsius (over 1,650 degrees Fahrenheit, or well past the point that aluminum or magnesium would melt) during testing, Ford and Carbon Revolution actually redesigned the wheels to "a thermal standard more suitable for motorsports," by adding an "incredibly thin, nearly diamond-hard coating that reliably shields the resin from heat." The same process was used to protect engine turbine blades on the Space Shuttle. While the work by Ford and Carbon Revolution should make GT350R customers excited, the work being done here could have serious implications for performance cars in the future. That's the real takeaway here, and is something that should leave fans of all performance vehicles excited.

2014 Ford Transit unveiled in Chassis Cab and Cutaway versions

As a leader in commercial vehicles here in the US, we knew Ford wouldn't take too long to show off the chassis cab and cutaway versions of its 2014 Ford Transit van. Set to go on sale this fall, Ford already revealed the full-body version of the Transit, and now it has pulled the cover off exposed-frame models just in time to to compete against the all-new Ram Promaster.
The term "chassis cab" refers to models with a fully enclosed cabin used for box vans or rental trucks, while cutaway models leave the cabin open behind the B-pillars for a pass-through on vehicles such as Class C motorhomes or ambulances. Both will offer three wheelbase options (138, 156 and 178 inches), the choice of single or dually rear axles, and plenty of upfitter-friendly touches including a pre-wired body harness and multiple body mount locations.
The new design will also help make upfitting a little easier since the fuel filler is now built into the cab (just behind the driver's door). Those integrated fuel filler necks will serve to feed either a 3.7-liter V6, a 3.5-liter EcoBoost V6, or a 3.2-liter Power Stroke diesel. Transit chassis cab and cutaways will wear varying Gross vehicle weight ratings from 9,000 pounds to 10,360 pounds depending on spec.

2015 Ford Mustang EcoBoost

Earlier this week, Ford invited us to Charlotte, NC, to ride in an all-new 2015 Mustang fitted with its turbocharged 2.3-liter EcoBoost four-cylinder. It's the first forced-induction, four-cylinder ponycar for the Blue Oval since the sun set on the 1986 Mustang SVO. We jumped at the opportunity, as only a handful of people have ever been in the passenger seat of this new car, and most automotive media won't get as close as we did until this fall.
As we revealed in our Deep Dive, Ford will slot this new turbocharged four as premium powerplant between its naturally aspirated 3.7-liter V6 and the naturally aspirated 5.0-liter V8. At last mention, the automaker said the direct-injected, all-aluminum engine will develop 305 horsepower and 300 pound-feet of torque, returning the best fuel economy of the three powerplants in the process. History buffs will note that those figures are appreciably stouter than the 200 horses and 240 lb-ft that the '86 SVO realized out of the same displacement, and the latter's figures were hugely impressive at the time. On paper, the new EcoBoost four looks to be a good fit for most owners who want to balance performance with efficiency - we were eager to see how it felt from the passenger seat.
Riding Notes