Find or Sell Used Cars, Trucks, and SUVs in USA

Ford F250 Custom on 2040-cars

Year:1978 Mileage:75100 Color: Red /
 Red
Location:

Clackamas, Oregon, United States

Clackamas, Oregon, United States
Transmission:Automatic
Body Type:Pickup Truck
Vehicle Title:Clear
Engine:351m
Fuel Type:Gasoline
For Sale By:Private Seller
VIN: F25HRCD134B Year: 1978
Number of Cylinders: 8
Make: Ford
Model: F-250
Trim: 2 door
Options: CB, CD Player
Drive Type: RWD
Mileage: 75,100
Sub Model: Custom
Disability Equipped: No
Exterior Color: Red
Warranty: Vehicle does NOT have an existing warranty
Interior Color: Red
Condition: UsedA vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections.Seller Notes:"The vehicle is a used truck and has age appropriate wear. Various dents chips and scratches throughout. Dash light is out. Sold as is, where is."

Ford F-250 for Sale

Auto Services in Oregon

Uncle Al`s Automotive Svc ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Automotive Tune Up Service
Address: 180 E Clarendon St, Aurora
Phone: (503) 457-4210

Tualatin Transmission Center ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Clutches
Address: 8240 SW Tonka St, Tualatin
Phone: (503) 691-1555

TRS 24Hr Towing, South Salem ★★★★★

Auto Repair & Service, Automotive Roadside Service, Marine Towing
Address: 4676 Commercial ST SE, Turner
Phone: (971) 600-2330

Town & Country Glass ★★★★★

Automobile Parts & Supplies, Glass-Auto, Plate, Window, Etc, Automobile Accessories
Address: 9427 SE Sun Crest Dr, Tualatin
Phone: (503) 284-5277

Tim`s Automotive ★★★★★

Auto Repair & Service, Used Car Dealers, Automobile Parts & Supplies
Address: 15688 SE 135th Ave, Damascus
Phone: (503) 656-0600

The Offroad Shop & Automotive Service ★★★★★

Auto Repair & Service
Address: 9952 SE Ash St, Oak-Grove
Phone: (503) 702-4996

Auto blog

Next-gen Ford Cobra Jet development underway, but will it be a Mustang?

Wed, 09 Oct 2013

Ford might be stepping away from the NHRA, but it isn't abandoning drag racing altogether. Hot Rod says that Ford confirmed a next-gen Cobra Jet factory drag racer is in the works, but the report also speculates that a new Cobra Jet could switch away from the Mustang nameplate.
Even though talk of a new Cobra Jet coincides with the all-new 2015 Mustang, the lack of confirmation for the dragster's platform leaves Hot Rod to guess that the car might switch to another platform - specifically a front-drive-based, unibody car like the Fusion or Taurus. We'd hate to think of a world with a NASCAR-ized dragster from Ford Racing, but it's also highly unlikely that the Mustang Cobra Jet would step away from its quarter-mile rivals like the Chevy COPO Camaro and Dodge Challenger Drag Pak.

Jay Leno takes a Surfin' Safari in a 1937 Ford Woodie Restomod

Tue, 21 Oct 2014

Woodie wagons were a major part of surfing culture in the 1960s, offering coastal style and a ton of room, and they even earned a mention in the Beach Boys' classic song Surfin' Safari. This week, Jay Leno's Garage takes a look at two modern, restomodded examples of these style icons.
Unlike a lot of restomods, builder Scott Bonowski keeps these wagons looking almost completely stock on the outside, and all of the upgrades are hidden underneath the timber. You can't tell by looking at it, but the '37 Woodie (pictured above) has independent front and rear suspension, disc brakes and a Ford 5.0-liter V8 under the hood.
Beyond the mechanical aspect, the craftsmanship into the wood is astounding. Bonowski claims there are between 30 and 50 coats of varnish on this wagon. It makes these woodies as much of a piece of fine furniture as a vehicle to drive.

Ford reveals new rapid prototyping and low-volume production techniques [w/video]

Mon, 08 Jul 2013

It's called "F3T," and that stands for Ford Free-form Fabrication Technology. The process that The Blue Oval has developed means being able to sidestep the weeks-long process of tool-and-die making when engineers want to construct a new part, allowing them to fabricate a three-dimensional part from a two-dimensional sheet of metal in just hours.
While F3T is being developed it is limited to "low-volume prototyping or even low-volume niche vehicles," but the next step is to evaluate it for use in Ford's global manufacturing facilities. You can find out more about it in the video and the press release below.