2001 Ford F-250 Super Duty Lariat Crew Cab Pickup 4-door 7.3l on 2040-cars

Auto blog

Ford recalling 2015 Mustang for fuel line leak, 20K Transit Connects for plastic panel

Ford is recalling 738 examples of the 2015 2015 Mustang with the 2.3-liter EcoBoost engine – 712 in the US, 16 in Canada. A fuel pressure sensor might have been installed incorrectly on the affected cars, and that could result in a fuel leak. At the time of writing the company hasn't heard any reports of any incidents related to the issue, and parties with affected vehicles can take them to the dealer to have the fuel tube assembly replaced free of charge. The 2014 Transit Connect Cargo Van is also the subject of a safety recall, due to a possible problem with adhesive used on the exterior plastic panel on the sliding doors. There are 19,825 units covered by that recall, which dealers will also repair free of charge. You can find more information on both bulletins in the press releases below. Ford Issues Safety Recall for Certain 2015 Mustang Vehicles in North America for Fuel Pressure Sensor Issue Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 730 2015 Ford Mustang vehicles in North America (actual 728) for a potential fuel line leak. A fuel pressure sensor, which is part of the fuel supply tube assembly, may have been installed incorrectly, potentially resulting in a pressurized fuel leak. A fuel leak in the presence of an ignition source may result in a fire. Ford is not aware of any fires, accidents or injuries related to this condition. Affected vehicles include certain 2015 Ford Mustangs equipped with 2.3-liter engines built at Flat Rock Assembly Plant, Sept. 25, 2014 to Oct. 9, 2014. Ford is aware of 712 vehicles in the United States and federalized territories and 16 in Canada. These totals are as of Dec. 3, 2014. Dealers will replace the fuel supply tube assembly at no cost to the customer. *** Ford Issues Safety Recall for Certain 2014 Transit Connect Cargo Van Vehicles in North America for Issue with the Plastic Panel on the Sliding Doors Dec 4, 2014 | DEARBORN, Mich. - Ford is issuing a safety recall for approximately 20,000 2014 Transit Connect cargo van vehicles in North America (actual 19,825) for an issue with adhesion of an exterior plastic panel to the sliding doors. This issue may result in noise, a water leak, a loose panel, or separation of the plastic panel from the vehicle while driving, potentially increasing the risk of an accident or injury. Ford is not aware of any accidents or injuries related to this condition.

UK's Loughborough University improving Ford's 1.0-litre EcoBoost engine

How much does it cost for college students to study zero emissions vehicles? At Loughborough University in the UK, a new Advanced Propulsion Centre (APC) is being built at a cost of a billion pounds ($1.7 billion US). The school has just announce that it will fund a number of grad student positions and is creating a new Chair in Advanced Propulsion Systems, which sounds like a fun job to us. We're weird like that. There will be a total of four professor-type positions in the new Center, including the chair, all focused on teaching students about low-carbon vehicle technologies, specifically electric and hybrid ones. The school is investing 1.5 million pounds ($2.5 million) for the new positions. There is a bigger picture as well, a 26-million pound ($44 million) Advanced Combustion Turbocharged Integrated Variable-valvetrain Engine (ACTIVE) project, which uses funds not only from the school but also from Ford and others. The point of ACTIVE is to study Ford's 1.0-liter EcoBoost engine and "improve further its efficiency and ensure it exceeds 2020 emission regulations." This is already a popular engine for the automaker, and it will need to stay at the bleeding edge of efficiency to remain as important in 2020 as it is today. Loughborough University has been working with automakers on advanced energy technologies for years, for example with Rolls-Royce and fuel cells in 2007 and the Lotus Hotfire engine in 2008. University invests GBP1.5M in advanced propulsion research to advance zero emissions vehicles challenge Loughborough University is investing GBP1.5M over five years in strategic research appointments, inspired by the global challenge to develop the new advanced propulsion technologies required for the move to zero emission vehicles. These appointments reinforce the University's world-class research in low-carbon vehicle technologies, adding new dimensions concerned with electric and hybrid drives. Four appointments will be made, including a Chair in Advanced Propulsion Systems, supported by a number of PhD studentships. The GBP1.5M investment is part of the University's commitment to the recently announced Advanced Propulsion Centre (APC) to support the development of new supply chains for low carbon vehicles. APC is an initiative established by the Automotive Council that will see GBP1 billion of investment from government and industry over the next 10 years.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: