2002 Ford F-150 Extended Cab 4x4 Pickup 5.4l V-8 Auto Clean Carfax No Reserve on 2040-cars

Auto blog

A cool boost to turbocharger performance

Since the advent of the forced-induction engine, we have been looking for ways to get every drop of performance we can. There are many approaches to getting additional power using better intercooling, water injection, or even adding nitrous oxide. One take on a short instant burst of power is being researched by Mahle and involves providing supercooled air to an engine, which allows it to burn a leaner fuel mixture and produce more power. The supercooling idea is not new and was examined by Ford in 1993 on the Mustang Mach III concept car, then brought up again in 2003 with the SVT F-150 Lightning concept. Ford called its system the SuperCooler; it was designed to work with any turbocharged or supercharged engine equipped with a water-to-air intercooler. The system on the Lightning concept used a small tank of antifreeze that was hooked up to the truck air conditioning compressor. The air conditioning compressor cooled the antifreeze down to about 30 degrees. The other side of the tank was hooked up to the air-to-water intercooler, which usually had a temperature over 100 degrees. Once the antifreeze was circulated from the tank into the intercooler, it would lower the intercooler temperature and provide for a cooler, denser air charge into the engine; the result was around 50 extra horsepower for a burst of about 30 seconds to a minute, depending on the size of the tank. The system for the Lightning was to be offered as a $750 option and would have been targeted towards drag racers and the like, as it could be used for a run down the drag strip and then re-cooled by the time the truck was back in line. The system was fairly non-intrusive – it only weighed about 25 pounds and did not require a new compressor or intercooler. But as with many concepts, it was ultimately scrapped. The technology was always stuck in the back of my mind, but with larger and more powerful engines being produced it could not find its place. With the advent of new fuel economy standards, we have seen small-displacement turbocharged engines pop up and they seem like the perfect candidate for this type of technology. Ford's EcoBoost 1.0-liter three-cylinder turbocharged engine, as used in the Fiesta and Focus, is one such candidate for this technology. It would add a negligent amount of weight but could provide a boost of 10 to 20 horsepower when needed, like merging onto the highway or catching up to traffic.

Ford reveals new rapid prototyping and low-volume production techniques [w/video]

It's called "F3T," and that stands for Ford Free-form Fabrication Technology. The process that The Blue Oval has developed means being able to sidestep the weeks-long process of tool-and-die making when engineers want to construct a new part, allowing them to fabricate a three-dimensional part from a two-dimensional sheet of metal in just hours.
While F3T is being developed it is limited to "low-volume prototyping or even low-volume niche vehicles," but the next step is to evaluate it for use in Ford's global manufacturing facilities. You can find out more about it in the video and the press release below.

Ford Gets The Aluminum F-150 Ready For Prime Time

Russell Barnett, a Ford dealer in Tennessee, is ready for aluminum. Ford is using the metal almost exclusively in body of the 2015 version of its best-selling F-150 pickup, which starts arriving at dealerships next month. Barnett is already answering customers' questions about the truck. And he's updated his repair shop not only for the F-150, but in anticipation that other Ford brands such as the Mustang will eventually make the switch from steel. But, just in case, he ordered some extra steel-bodied 2014 pickups. "There will be some people who won't want to change for a while," says Barnett, who says pickups make up around half of the annual sales at his dealership in rural Winchester. Ford is doubling down on aluminum, which is lighter - and more expensive - than steel but just as tough. The new truck is the company's response to customers' requests for a more fuel-efficient and nimbler pickup. Fordhopes the advantages outweigh customer doubts about the durability of aluminum or potential repair costs for the pricier metal. It's a big risk. So far this year, one out of every three vehicles Ford sold in the U.S. was an F-Series pickup. Morgan Stanley estimates F-Series trucks account for 90 percent of Ford's global automotive profit. On Tuesday, it kicked off production of the new truck at its Dearborn Truck Plant, four miles from the company's headquarters. "Yeah, this is a risk, but it's one well worth taking." said Bill Ford, the company's executive chairman, as he stood alongside the assembly line. "For our customer, this is a big, big leap forward." The trucks have been the best-selling vehicles in the U.S. for 32 straight years; last year, Ford sold nearly 100,000 more full-size pickups than General Motors. Aluminum isn't new to the auto industry, but this is the first time it will cover the entire body of such a high-volume vehicle. Ford made 647,697 F-150 pickups at its two U.S. plants last year; that's one every 49 seconds. If Ford's bet pays off, it could pad its lead in the lucrative truck market. More importantly, aluminum "future proofs" the truck - and the company - in an era of rising fuel economy standards, says Karl Brauer, a senior analyst with Kelley Blue Book. Ford will announce the truck's fuel economy figures later this month. That could determine if it steals customers away from the Silverado or Ram. Truck buyers are among the most loyal in the auto market.