No Reserve 1969 Bronco 2 Owner, Original Paint, 89k Miles, 4x4 Hardtop P/s, Auto on 2040-cars

Auto blog

Saleen previews new 302 Mustang

The introduction of a new generation of a model like the Ford Mustang may be exciting enough in its own right for enthusiasts, but that's just the tip of the proverbial iceberg, because you know that Ford itself as well as numerous aftermarket tuners will soon follow up with even more desirable versions. And few Mustang tuners carry quite the same clout of Saleen.
Recently reunited after its previous split, Saleen is back on the map and hard at work on new aftermarket modifications for a wide array of muscle cars. We knew it would only be a matter of time before it would release a new 302 Mustang, and now it's sent out the first image to show us what to expect.
Details are scarce, but House that Steve Built says the 2015 Saleen 302 Mustang "is perfectly positioned as the next American exotic." And it should know, considering that it's the same outfit that produced the Saleen S7 that really was a true American exotic. From the teaser image above we can see that Saleen has given its Mustang a new front air dam, a very wide air scoop on the hood and of course Saleen's trademark slat grille.

Ford Announces Four Recalls, 1.4M Vehicles Affected

Ford is taking a bit of the spotlight away from General Motors, announcing a major group of recall campaigns, covering a total of 1.4 million vehicles built between 2006 and 2013. Let's start with the big one, which covers the Ford Escape, Mercury Mariner and, according to The Detroit News, Ford-built Mazda Tribute CUVs. 915,216 vehicles are covered, all of which were built in model years 2008 to 2011. 736,000 vehicles are in the US, while Canada then Mexico make up the vast majority of the remainder. The problem is due to an issue with the torque sensor in the steering column, which could lead to sudden power steering failure. Manual steering would still be available, though. "Dealers will perform one of three service fixes, depending upon what diagnostic codes are shown when the vehicle is taken to the dealer," Ford spokeswoman Kelli Felker wrote to Autoblog in an email. "They will either update software for the power steering control module and the instrument cluster module; replace the torque sensor; or replace the steering column, which includes upgraded power steering control module software." The most recent generation of the Ford Explorer is suffering from a similar malady, thanks to an intermittent electrical connection (we think that means short circuit) in the steering column. Like the Escape and Mariner, manual steering would still be available in the event of a power failure. Ford will recall 195,527 examples of its Explorer, 177,500 of which are in the US. This recall covers model years 2011 to 2013. According to Automotive News, the National Highway Traffic Safety Administration has stated that Ford will inform owners of affected vehicles by July 25. Ford is also recalling 200,000 Taurus sedans, over a corrosion issue in the license plate lamp. This particular recall, which covers vehicles from model years 2010 to 2014, is limited to drivers in northern climes. Vehicle owners in southern states are free to pass on the recall. Finally, 82,576 Fusion, Mercury Milan and Lincoln Zephyr/MKZ sedans from 2006 to 2011 are being recalled because of floormats that can interfere with the accelerator pedal. Dealers will replace the offensive floormats with newer examples. "Ford is committed to providing our customers with top quality vehicles. We are equally committed to addressing potential issues and responding quickly for our customers," Felker wrote.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.