99 Dodge Ram 2500 4x4 on 2040-cars

Auto blog

2020 Dodge Challenger Drag Pak comes solely with supercharged power

The Dodge Challenger Drag Pak has returned for 2020, five years after the last one arrived, and two years after it began development. And while in many ways it looks like past Drag Paks, there are a number of tweaks that should make this the fastest and most capable factory drag car yet from Mopar. Unlike the last model, only a supercharged 354-cubic-inch (5.8-liter for the imperically challenged) V8 is available. Mopar says it's more powerful than its predecessor, though exact horsepower wasn't given. It did confirm that the previous car was capable of a stunning 1,200 horsepower. The engine is coupled solely to a three-speed automatic transmission with a manual shifter. 2020 Dodge Challenger Drag Pak View 17 Photos Supporting the massive engine are many chassis, suspension and driveline enhancements. The independent rear suspension and axles are gone in favor of a solid axle from Strange and a four-link suspension. The front remains stock except for double-adjustable Bilstein shocks. The engine is mounted to a subframe member that's beneficial both to weight distribution and center of gravity. The car gets high-performance brakes and custom Weld Racing wheels with "DRAGPAK" engraved on them. The interior features a welded-in roll cage certified for quarter-mile times as quick as 7.5 seconds. Helping keep the car planted without increasing drag too much are front and rear spoilers from the road-going Challenger, a new addition compared with the previous car. Every Drag Pak car also comes standard with a wheelie bar and parachute. Dodge will only build 50 of these cars, and they'll only be offered as race cars that aren't legal for the street. The cars will be eligible for competing in sportsman classes in NHRA and NMCA drag racing series. Pricing and availability hasn't been set yet, but will be revealed sometime next year.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

The Dodge Demon is leaked in Fast 8 video with Vin Diesel

It's only week two of the twelve-part Dodge Demon teaser roll out, and it already appears the metaphorical Hellcat is out of the bag. A YouTube video featuring Vin Diesel discussing The Fate of the Furious ( Fast 8) has what are almost certainly two Dodge Challenger Demons parked right in the background. So much for three months worth of build up and mystique. The two cars in the video appear to have the new logo affixed to the fender, right where the current Hellcat logo resides. In addition, the wheels and the massive hood scoop both appear to be the same relative shape as the ones briefly flashed in the latest teaser video. While we can't be 100 percent certain this is really a Demon, all the evidence points to yes. Even if this spoiled Dodge's plans, actually seeing the car here makes us even more excited for the full reveal. We still don't know all the final specs, save that it'll be 200 lbs lighter, so there is still some mystery to be had. The Challenger and Charger Hellcat twins, some of the most brazen and brutish machines currently on the road, were already cranked up to 11. The Demon, with its wide fender flares and comically large hood scoop looks makes the standard car look tame by comparison. We can't wait. Related Video: News Source: YouTube Design/Style Dodge Coupe Performance dodge demon Vin Diesel dodge hellcat dodge challenger hellcat