2004 Dodge Ram 2500 Diesel 4x4 Slt Long Bed 1 Texas Owner on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

2020 Dodge Charger SRT Hellcat Widebody Daytona 50th Anniversary Edition celebrates an icon

Fifty years ago, Dodge commissioned Creative Industries to build the 1969 Dodge Charger Daytona as a homologation special to satisfy NASCAR rules. The extraterrestrial-looking coupe conquered at the race track, broke records, and frightened any onlooker possessed of a weak constitution; it's claimed that even the carmaker's general manager at the time, Bob McCurry, considered the Charger Daytona the ugliest car he'd ever laid eyes on. Time having worked its magic, Dodge is celebrating the now-iconic Winged Warrior with the 2020 Charger SRT Hellcat Widebody Daytona 50th Anniversary Edition. The new model goes without a nose cone and vertical stabilizers, but it does loose 717 horsepower from its 6.2-liter supercharged V8, which is 10 more than the standard car. The grunty sedan will be available in four colors: Pitch Black, Triple Nickel, White Knuckle, and B5 Blue exclusive to this model. B5 was the original paint code for a Blue Fire Poly hue available on Dodge and Plymouth products built between 1969 and 1972. Evoking the original as well as highlighting the decklid spoiler on the new Charger, the black, nickel, and blue sedans get white "Daytona" decals on the rear quarter panels and a white spoiler, matching white Hellcat badges on the front fenders. White cars get blue "Daytona" decals and spoiler, and Hellcat badges in a bright finish. Twenty-inch Warp Speed wheels finished in Satin Carbon on all-season Pirellis and black Brembo brakes complete the exterior overhaul. Inside, heated and cooled 12-way adjustable performance seats are trimmed in Nappa leather and Alcantara, with blue cross-stitching joining seatbacks embroidered with the word "Daytona." The flat-bottomed, suede-wrapped steering wheel with silver stitching and "velour-bound" floor mats will only come in this model, the festival of special appointments also including the dynamica suede headliner, carbon fiber instrument panel and bezels, light black chrome trim pieces, and blue stitching on the dash, shifter, center console armrest, and door panels. Dodge will only produce 501 units, said to match the number of cars necessary for NASCAR homologation at the time, and each wears a plaque identifying it as "X out of 501." NASCAR rules in 1969 demanded 500 units, actually — the car Dodge built in 1968 to race was called the Charger 500, in fact. Also, Creative Industries built 503 1969 Charger Daytonas for the U.S. and another 40 for Canada, but who's counting?

Marchionne says no offers are on the table for Fiat Chrysler

MONZA, Italy (Reuters) - Fiat Chrysler (FCA) has not received any offer for the company nor is the world's seventh-largest carmaker working on any "big deal", Chief Executive Sergio Marchionne said on Saturday. Speaking on the sidelines of the Italian Formula One Grand Prix, Marchionne said the focus remained on executing the company's business plan to 2018. Asked whether FCA had been approached by someone or whether there was an offer on the table, he simply said: "No." The company's share price jumped to record highs last month after reports of interest for the group or some of its brands from China. China's Great Wall Motor Co Ltd openly said it was interested in FCA, but had not held talks or signed a deal with executives at the Italian-American automaker. The stock move was also helped by expectations that the company might separate from some of its units. Marchionne reiterated on Saturday that FCA was working on a plan to "purify" its portfolio and that units, such as the components businesses, would be separated from the group. He hopes to complete that process by the end of 2018. "There are activities within the group that do not belong to a car manufacturer, for example the components businesses. The group needs to be cleared of those things," he told journalists. Asked whether an announcement could come this year, Marchionne said it was up to the board to decide and that it would next meet at the end of September. He said the time was not right for a spin-off of luxury brand Maserati and premium Alfa Romeo and the two brands needed to become self-sustainable entities first and "have the muscle to stand on their feet, make sufficient cash". "The way we see it now, it's almost impossible, if not impossible, to see a spin-off of Alfa Romeo/Maserati, these are two entities that are immature and in a development phase," he said. "It's the wrong moment, we are not in a condition to do it." He said the concept of separating the two brands from FCA's mass market business made sense and did not rule out this happening in future, but not under his tenure, which lasts until April 2019. "If there is an opportunity in future, it would certainly happen after I'm gone. It won't happen while Marchionne is around," he said.