10 White 3.3l V6 Grand Caravan C/v *cargo Mat & Cage *sliding Rear Doors *fl on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Watch a Dodge Viper driver show off his V10 all the way into a wall

Has there ever been a show-off video that doesn't end terribly? This video clip captured with a cellphone shows the driver of a neon green Viper GTS giving a fellow motorist a couple throttle blips to signify his intent – which seems to be to crash the Viper into a concrete wall as quickly as possible. It's not pretty. The mean machine seems to be a second-generation Viper GTS in Stryker Green. To our knowledge, no photos have surfaced of the aftermath, so we wish both the driver and their most-likely bruised ego a speedy recovery. Who knows, maybe the Viper is also salvageable.

SpeedKore carbon-fiber 1970 Dodge Charger packs a 996-hp Demon engine

SpeedKore Performance does some pretty neat things with carbon fiber. SEMA is always the place to show off new and interesting builds, and SpeedKore has a few new offerings on display. We talked about the lightweight carbon fiber 2018 Dodge Demon late last week, but now that SEMA 2018 is in full swing, we've got a look at something even cooler, an all-carbon, Demon-powered 1970 Dodge Charger "Evolution." SpeedKore Performance is based in Wisconsin and has been churning out SEMA showstoppers for years. In addition to the Demon, take a look at this Shelby GT350R the shop modified a few years back. The Charger Evolution is named so because it further modifies the SpeedKore Charger "Tantrum" that was used in the " Fast and Furious" films. That car used a carbon composite body and was fitted with a 9.0-liter Mercury Racing twin-turbo engine making an absurd 1,650 horsepower. The Evolution might be down on power — only 996 horses thanks to a modified Demon crate engine — but the goal was to create something a little more usable than the Tantrum. Upgrades include a smaller supercharger pulley, larger fuel injectors, a custom cold-air intake, stainless steel headers and a custom exhaust with SLP mufflers. There's also a Dailey Engineering dry sump, upgraded oil cooler, and Saldana radiator. It's also lighter, thanks to even more carbon fiber. SpeedKore had a goal to get the '70 Charger to about 3,200 pounds. To get there, the Evolution employs carbon-fiber bodywork, an aluminum floor, a steel roll cage and a new 2x3-inch steel box frame. SpeedKore's autoclave is large enough to bake a one-piece roof, hood and quarter panels. The bare bodywork has been finished with a clear coat to help prevent fading. The Evolution uses billet aluminum for the door handles, fuel cap and grille, all finished in a bronze-nickel coating to pair with the HRE wheels. In addition to the floor, aluminum was used for the firewall, transmission tunnel and radiator shroud. To slow the Charger down, it uses Brembo brakes with six-piston calipers up front and four-piston calipers in the rear. The suspension uses Penske adjustable coilovers while Michelin Pilot Sport 2 tires wrap 19x10-inch front wheels and 20x12-inch rear wheels. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.